In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire?

Explore Courses UPSC Exam UPSC Test Series Free Notes EduRev Infinity

Open App

Class 12 Exam > Class 12 Questions > In a meter bridge experiment, the null point ...

Join the Discussion on the App

In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire?

Join for Free

Join for Free

Most Upvoted Answer

In a meter bridge experiment, the null point should be near centre of ...

Correct option is 'a'

View all answers Start learning for free

Explore Courses for Class 12 exam

Similar Class 12 Doubts

In a potentiometer experiment, for measuring internal resistance of a cell, the balance point has been obtained on the fourth wire. The balance point can be shifted to fifth wire by

View answer

Read the following text and answer the following questions on the basis of the same:In one of his experiments on interference, August Jean Fresnel used a biprism to induce interference between two beams. He split a diverging beam of light into two parts by using the biprism to refract them. This resulted in two split beams which acted as if they were from two coherent sources and which therefore interfered with each other.A Fresnel Biprism is a thin double prism placed base to base and have very small refracting angle ( 0.5°). This is equivalent to a single prism with one of its angle nearly 179° and other two of 0.5° each.In Young’s double Slits experiment, a single source is split in two coherent sources. For the Young’s slits experiment, we must approximate that the slits act as point sources. This however is not the case, since the slits have finite width. In this way, it gives rise to unwanted diffraction effects that causes errors.The Fresnel biprism experiment overcomes this problem.A Fresnel biprism is a variation of Young’s Slits experiment. When monochromatic light through a narrow slit falls on biprism that divides it into two components. One of these component is refracted from upper portion of biprism and the other one refracted through lower portion. Two virtual coherent sources formed from the original source. In this case, two virtual coherent sources are point sources and replace slits in Young’s experiment.Q. The Fresnel biprism is

View answer

If an ammeter is to be used in place of a voltmeter then we must connect with the ammeter of (

View answer

A to ohm resistance with an unknown resistance are in series connected to the Potentiometer arranged having a constant current in its primary circuit if potential difference across 2 ohm resistance is balance at 300 CM length and potential difference across unknown resistance is balance at 360 CM then unknown resistance is A. 8.4 ohm B. 1ohm C .2.4ohm D.4.6 ohm?

View answer

Resistances n, each of r ohm, when connectedin parallel give an equivalent resistance of Rohm. If these resistances were connected inseries, the combination would have a resistancein ohms, equal to [2004]

View answer

Share with a Friend

Answer this doubt

Question Description
In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire? for Class 12 2024 is part of Class 12 preparation. The Question and answers have been prepared according to the Class 12 exam syllabus. Information about In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire? covers all topics & solutions for Class 12 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire?.

Solutions for In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire? in English & in Hindi are available as part of our courses for Class 12. Download more important topics, notes, lectures and mock test series for Class 12 Exam by signing up for free.

Here you can find the meaning of In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire? defined & explained in the simplest way possible. Besides giving the explanation of In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire?, a detailed solution for In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire? has been provided alongside types of In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire? theory, EduRev gives you an ample number of questions to practice In a meter bridge experiment, the null point should be near centre of the bridge to minimize error due to: A) End resistance B) Contact resistance C) Non uniformity of the wire D) Overheating of wire? tests, examples and also practice Class 12 tests.

Explore Courses for Class 12 exam