Mechanical Engineering Exam > Mechanical Engineering Questions > Select the WRONG statement:a)The rivet will b...
Start Learning for Free
Select the WRONG statement:
- a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.
- b)The rivet will be in double shear in case of butt joints with double cover straps.
- c)A butt joint with two cover plates should be used for circumferential joint in boilers.
- d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.
Correct answer is option 'C'. Can you explain this answer?
| FREE This question is part of | Download PDF Attempt this Test |
Most Upvoted Answer
Select the WRONG statement:a)The rivet will be in single shear in case...
Wrong Statement: c) A butt joint with two cover plates should be used for circumferential joint in boilers.
Explanation:
A butt joint is a type of joint where two plates are joined together by overlapping their edges and then joining them using rivets or other fasteners. A circumferential joint, on the other hand, refers to a joint that runs along the circumference of a cylindrical structure, such as a boiler.
Butt Joint with Two Cover Plates:
In the case of a circumferential joint in boilers, a butt joint with two cover plates is not typically used. This is because a butt joint with two cover plates would result in excessive thickness and weight, which is not desirable for boilers.
Alternative Joint for Circumferential Joint in Boilers:
The preferred joint for a circumferential joint in boilers is a lap joint. A lap joint involves overlapping the edges of the plates and then joining them using rivets or other fasteners. This type of joint provides sufficient strength and durability while minimizing the thickness and weight of the joint.
Advantages of Lap Joint:
1. Weight Reduction: A lap joint with a single cover strap reduces the overall weight of the joint compared to a butt joint with two cover plates.
2. Ease of Installation: A lap joint is relatively easier to install compared to a butt joint with two cover plates.
3. Cost Savings: Using a lap joint instead of a butt joint with two cover plates can result in cost savings due to reduced material and labor requirements.
Conclusion:
In summary, the wrong statement is c) A butt joint with two cover plates should be used for a circumferential joint in boilers. Instead, a lap joint with a single cover strap is typically used for circumferential joints in boilers due to its advantages of weight reduction, ease of installation, and cost savings.
Explanation:
A butt joint is a type of joint where two plates are joined together by overlapping their edges and then joining them using rivets or other fasteners. A circumferential joint, on the other hand, refers to a joint that runs along the circumference of a cylindrical structure, such as a boiler.
Butt Joint with Two Cover Plates:
In the case of a circumferential joint in boilers, a butt joint with two cover plates is not typically used. This is because a butt joint with two cover plates would result in excessive thickness and weight, which is not desirable for boilers.
Alternative Joint for Circumferential Joint in Boilers:
The preferred joint for a circumferential joint in boilers is a lap joint. A lap joint involves overlapping the edges of the plates and then joining them using rivets or other fasteners. This type of joint provides sufficient strength and durability while minimizing the thickness and weight of the joint.
Advantages of Lap Joint:
1. Weight Reduction: A lap joint with a single cover strap reduces the overall weight of the joint compared to a butt joint with two cover plates.
2. Ease of Installation: A lap joint is relatively easier to install compared to a butt joint with two cover plates.
3. Cost Savings: Using a lap joint instead of a butt joint with two cover plates can result in cost savings due to reduced material and labor requirements.
Conclusion:
In summary, the wrong statement is c) A butt joint with two cover plates should be used for a circumferential joint in boilers. Instead, a lap joint with a single cover strap is typically used for circumferential joints in boilers due to its advantages of weight reduction, ease of installation, and cost savings.
Attention Mechanical Engineering Students!
To make sure you are not studying endlessly, EduRev has designed Mechanical Engineering study material, with Structured Courses, Videos, & Test Series. Plus get personalized analysis, doubt solving and improvement plans to achieve a great score in Mechanical Engineering.
|
Explore Courses for Mechanical Engineering exam
|
|
Similar Mechanical Engineering Doubts
Top Courses for Mechanical EngineeringView all
Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer?
Question Description
Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer? for Mechanical Engineering 2024 is part of Mechanical Engineering preparation. The Question and answers have been prepared according to the Mechanical Engineering exam syllabus. Information about Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer? covers all topics & solutions for Mechanical Engineering 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer?.
Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer? for Mechanical Engineering 2024 is part of Mechanical Engineering preparation. The Question and answers have been prepared according to the Mechanical Engineering exam syllabus. Information about Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer? covers all topics & solutions for Mechanical Engineering 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer?.
Solutions for Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer? in English & in Hindi are available as part of our courses for Mechanical Engineering.
Download more important topics, notes, lectures and mock test series for Mechanical Engineering Exam by signing up for free.
Here you can find the meaning of Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer? defined & explained in the simplest way possible. Besides giving the explanation of
Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer?, a detailed solution for Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer? has been provided alongside types of Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer? theory, EduRev gives you an
ample number of questions to practice Select the WRONG statement:a)The rivet will be in single shear in case of lap joints and butt joint with single cover strap.b)The rivet will be in double shear in case of butt joints with double cover straps.c)A butt joint with two cover plates should be used for circumferential joint in boilers.d)According to IBR, the thickness of the straps in a butt joint should not be less than 10 mm.Correct answer is option 'C'. Can you explain this answer? tests, examples and also practice Mechanical Engineering tests.
|
|
Explore Courses for Mechanical Engineering exam
|
|
Suggested Free Tests
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
|
© EduRev
|
Education Revolution
|
Follow Us
|
Signup to see your scores
go up within 7 days!
Access 1000+ FREE Docs, Videos and Tests
Takes less than 10 seconds to signup