Mechanical Engineering Exam > Mechanical Engineering Questions > Design the general type of GO and NO GO gauge...
Start Learning for Free
Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation
of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance?
of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance?
Most Upvoted Answer
Design the general type of GO and NO GO gauge for components having 30...
General Type of GO and NO GO Gauge Design:
Fit Type:
- The components have a 30 H7/f8 fit.
Gauge Design Equations:
- The formula for the GO gauge is i=0.453D + 0.001D.
- The upper deviation of the 'f' shaft is -5.5D^0.41.
Gauge Tolerance Calculation:
- The diameter falls in the range of 18-30mm.
- IT7 tolerance class is 16i.
- IT8 tolerance class is 25i.
Wear Allowance:
- The wear allowance is 10% of the gauge tolerance.
Explanation:
- To design the GO and NO GO gauges for the components with a 30 H7/f8 fit, we first calculate the values using the given formulas for the GO gauge and the upper deviation of the 'f' shaft.
- We then determine the gauge tolerance based on the diameter range and the tolerance classes IT7 and IT8.
- Finally, we apply the wear allowance to ensure that the gauges can accommodate wear over time without compromising the fit.
- By following these steps, we can design effective GO and NO GO gauges for components with a 30 H7/f8 fit.
Fit Type:
- The components have a 30 H7/f8 fit.
Gauge Design Equations:
- The formula for the GO gauge is i=0.453D + 0.001D.
- The upper deviation of the 'f' shaft is -5.5D^0.41.
Gauge Tolerance Calculation:
- The diameter falls in the range of 18-30mm.
- IT7 tolerance class is 16i.
- IT8 tolerance class is 25i.
Wear Allowance:
- The wear allowance is 10% of the gauge tolerance.
Explanation:
- To design the GO and NO GO gauges for the components with a 30 H7/f8 fit, we first calculate the values using the given formulas for the GO gauge and the upper deviation of the 'f' shaft.
- We then determine the gauge tolerance based on the diameter range and the tolerance classes IT7 and IT8.
- Finally, we apply the wear allowance to ensure that the gauges can accommodate wear over time without compromising the fit.
- By following these steps, we can design effective GO and NO GO gauges for components with a 30 H7/f8 fit.
Attention Mechanical Engineering Students!
To make sure you are not studying endlessly, EduRev has designed Mechanical Engineering study material, with Structured Courses, Videos, & Test Series. Plus get personalized analysis, doubt solving and improvement plans to achieve a great score in Mechanical Engineering.
|
Explore Courses for Mechanical Engineering exam
|
|
Similar Mechanical Engineering Doubts
Top Courses for Mechanical EngineeringView all
Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance?
Question Description
Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance? for Mechanical Engineering 2024 is part of Mechanical Engineering preparation. The Question and answers have been prepared according to the Mechanical Engineering exam syllabus. Information about Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance? covers all topics & solutions for Mechanical Engineering 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance?.
Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance? for Mechanical Engineering 2024 is part of Mechanical Engineering preparation. The Question and answers have been prepared according to the Mechanical Engineering exam syllabus. Information about Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance? covers all topics & solutions for Mechanical Engineering 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance?.
Solutions for Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance? in English & in Hindi are available as part of our courses for Mechanical Engineering.
Download more important topics, notes, lectures and mock test series for Mechanical Engineering Exam by signing up for free.
Here you can find the meaning of Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance? defined & explained in the simplest way possible. Besides giving the explanation of
Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance?, a detailed solution for Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance? has been provided alongside types of Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance? theory, EduRev gives you an
ample number of questions to practice Design the general type of GO and NO GO gauge for components having 30 H7/f8 fit. Given that (a) i=0.453D + 0.001D (b) upper deviation of 'f' shaft = -5.5D0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7=16i (e) IT8=25i (f) wear allowance = 10% of gauge tolerance? tests, examples and also practice Mechanical Engineering tests.
|
|
Explore Courses for Mechanical Engineering exam
|
|
Suggested Free Tests
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
|
© EduRev
|
Education Revolution
|
Follow Us
|
Signup to see your scores
go up within 7 days!
Access 1000+ FREE Docs, Videos and Tests
Takes less than 10 seconds to signup