Software Development Exam > Software Development Questions > LAN & Subnetting ExercisesScenario 1: A netwo...
Start Learning for Free
LAN & Subnetting Exercises
Scenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?
1. A crossover cable should be used in place of the straight-through cable.
2. A rollover cable should be used in place of the straight-through cable.
3. The subnet masks should be set to 255.255.255.192.
4. A default gateway needs to be set on each host.
5. The subnet masks should be set to 255.255.255.0.
1 only
2 only
3 and 4 only
1 and 5 only
2 and 5 only
ANSWER:
explain the answer?
Scenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?
1. A crossover cable should be used in place of the straight-through cable.
2. A rollover cable should be used in place of the straight-through cable.
3. The subnet masks should be set to 255.255.255.192.
4. A default gateway needs to be set on each host.
5. The subnet masks should be set to 255.255.255.0.
1 only
2 only
3 and 4 only
1 and 5 only
2 and 5 only
ANSWER:
explain the answer?
Most Upvoted Answer
LAN & Subnetting ExercisesScenario 1: A network administrator is conne...
Understanding the Scenario
In the scenario, hosts A and B are directly connected through their Ethernet interfaces but are unable to communicate. This can often be attributed to issues related to cabling, subnetting, or configuration settings.
Possible Solutions
- Crossover Cable vs. Straight-through Cable:
- A crossover cable is needed for direct connections between two devices of the same type (like two PCs). A straight-through cable is typically used to connect different devices (like a PC to a switch). Thus, using a crossover cable is a requirement for proper communication.
- Rollover Cable:
- A rollover cable is used for console connections to network devices (like routers and switches). It is not applicable for direct host-to-host connections and will not solve the communication issue.
- Subnet Masks:
- Setting the subnet masks to 255.255.255.192 would create four subnets, which is unnecessary for a direct connection. The subnet masks should ideally be set to 255.255.255.0, which allows both hosts to be in the same subnet and communicate directly.
- Default Gateway:
- A default gateway is not required for direct communication over the same subnet. It is only necessary when hosts need to communicate with devices outside their local network.
Conclusion
The best course of action is to use a crossover cable and set the subnet masks to 255.255.255.0. Therefore, the correct option is:
- 1 and 5 only
This combination will ensure that both hosts A and B can communicate effectively.
In the scenario, hosts A and B are directly connected through their Ethernet interfaces but are unable to communicate. This can often be attributed to issues related to cabling, subnetting, or configuration settings.
Possible Solutions
- Crossover Cable vs. Straight-through Cable:
- A crossover cable is needed for direct connections between two devices of the same type (like two PCs). A straight-through cable is typically used to connect different devices (like a PC to a switch). Thus, using a crossover cable is a requirement for proper communication.
- Rollover Cable:
- A rollover cable is used for console connections to network devices (like routers and switches). It is not applicable for direct host-to-host connections and will not solve the communication issue.
- Subnet Masks:
- Setting the subnet masks to 255.255.255.192 would create four subnets, which is unnecessary for a direct connection. The subnet masks should ideally be set to 255.255.255.0, which allows both hosts to be in the same subnet and communicate directly.
- Default Gateway:
- A default gateway is not required for direct communication over the same subnet. It is only necessary when hosts need to communicate with devices outside their local network.
Conclusion
The best course of action is to use a crossover cable and set the subnet masks to 255.255.255.0. Therefore, the correct option is:
- 1 and 5 only
This combination will ensure that both hosts A and B can communicate effectively.
Attention Software Development Students!
To make sure you are not studying endlessly, EduRev has designed Software Development study material, with Structured Courses, Videos, & Test Series. Plus get personalized analysis, doubt solving and improvement plans to achieve a great score in Software Development.
|
Explore Courses for Software Development exam
|
|
Top Courses for Software DevelopmentView all
LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer?
Question Description
LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer? for Software Development 2024 is part of Software Development preparation. The Question and answers have been prepared according to the Software Development exam syllabus. Information about LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer? covers all topics & solutions for Software Development 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer?.
LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer? for Software Development 2024 is part of Software Development preparation. The Question and answers have been prepared according to the Software Development exam syllabus. Information about LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer? covers all topics & solutions for Software Development 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer?.
Solutions for LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer? in English & in Hindi are available as part of our courses for Software Development.
Download more important topics, notes, lectures and mock test series for Software Development Exam by signing up for free.
Here you can find the meaning of LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer? defined & explained in the simplest way possible. Besides giving the explanation of
LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer?, a detailed solution for LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer? has been provided alongside types of LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer? theory, EduRev gives you an
ample number of questions to practice LAN & Subnetting ExercisesScenario 1: A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?1. A crossover cable should be used in place of the straight-through cable.2. A rollover cable should be used in place of the straight-through cable.3. The subnet masks should be set to 255.255.255.192.4. A default gateway needs to be set on each host.5. The subnet masks should be set to 255.255.255.0.1 only2 only3 and 4 only1 and 5 only2 and 5 onlyANSWER: explain the answer? tests, examples and also practice Software Development tests.
|
|
Explore Courses for Software Development exam
|
|
Suggested Free Tests
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
|
© EduRev
|
Education Revolution
|
Follow Us
|
Signup to see your scores
go up within 7 days!
Access 1000+ FREE Docs, Videos and Tests
Takes less than 10 seconds to signup