JEE Exam > JEE Notes > DC Pandey Solutions for JEE Physics > DC Pandey Solutions (JEE Main): Elasticity
DC Pandey Solutions (JEE Main): Elasticity | DC Pandey Solutions for JEE Physics PDF Download
| Download, print and study this document offline |
Please wait while the PDF view is loading
Page 1
EXERCISES
For JEE Main
Subjective Questions
Q 1. A cylindrical steel wire of 3 m length is to stretch no more than 0.2 cm when a tensile force of 400
N is applied to each end of the wire. What minimum diameter is required for the wire ?
Ysteel =2.1 × 10
11
N/m
2
Q 2. The elastic limit of a steel cable is 3.0 × 10
8
N/m
2
and the cross-section area is 4 cm
2
. Find the
maximum upward acceleration that can be given to a 900 kg elevator supported by the cable if the
stress is not to exceed one-third of the elastic limit.
Q 3. If the elastic limit of copper is 1.5 x 10
8
N/m
2
, determine the minimum diameter a copper wire can
have under a load of 10.0 kg, if its elastic limit is not to be exceeded.
Q 4. Find the increment in the length of a steel wire of length 5 m and radius 6 mm under its own
weight. Density of steel = 8000 kg/m
3
and Young's modulus of steel = 2 x 10
11
N/m
2
. What is the
energy stored in the wire ? (Take g = 9.8m/s
2
)
Q 5. Two wires shown in figure are made of the same material which has a breaking stress of 8 × 10
8
N/m
2
. The area of cross-section of the upper wire is 0.006 cm
2
and that of the lower wire is 0.003
cm . The mass m 1 = 10 kg, m 2 = 20 kg and the hanger is light. Find the maximum load that can be
put on the hanger without breaking a wire. Which wire will break first if the load is increased ?
(Take g = 10 m/s
2
)
Q 6. A steel wire and a copper wire of equal length and equal cross-sectional area are joined end to end
and the combination is subjected to a tension. Find the ratio of:
(a) the stresses developed in the two wires,
(b) the strains developed. (Y of steel =2 × 10
11
N/m
2
and T of copper = 1.3 × 10
11
N/m
2
)
Q 7. Calculate the approximate change in density of water in a lake at a depth of 400 m below the
surface. The density of water at the surface is 1030 kg/m
3
and bulk modulus of water is 2 ×
10
9
N/m
2
.
Q 8. A wire of length 3 m, diameter 0.4 mm and Young's modulus 8 × 10
10
N/m
2
is suspended from a
point and supports a heavy cylinder of volume 10
-3
m
3
at its lower end. Find the decrease in length
when the metal cylinder is immersed in a liquid of density 800 kg/m
3
.
Q 9. In taking a solid ball of rubber from the surface to the bottom of a lake of 180 m depth, reduction
in the volume of the ball is 0.1%. The density of water of the lake is 1 × 10
3
kg/m . Determine the
value of the bulk modulus of elasticity of rubber. (g = 9.8m/s
2
)
Page 2
EXERCISES
For JEE Main
Subjective Questions
Q 1. A cylindrical steel wire of 3 m length is to stretch no more than 0.2 cm when a tensile force of 400
N is applied to each end of the wire. What minimum diameter is required for the wire ?
Ysteel =2.1 × 10
11
N/m
2
Q 2. The elastic limit of a steel cable is 3.0 × 10
8
N/m
2
and the cross-section area is 4 cm
2
. Find the
maximum upward acceleration that can be given to a 900 kg elevator supported by the cable if the
stress is not to exceed one-third of the elastic limit.
Q 3. If the elastic limit of copper is 1.5 x 10
8
N/m
2
, determine the minimum diameter a copper wire can
have under a load of 10.0 kg, if its elastic limit is not to be exceeded.
Q 4. Find the increment in the length of a steel wire of length 5 m and radius 6 mm under its own
weight. Density of steel = 8000 kg/m
3
and Young's modulus of steel = 2 x 10
11
N/m
2
. What is the
energy stored in the wire ? (Take g = 9.8m/s
2
)
Q 5. Two wires shown in figure are made of the same material which has a breaking stress of 8 × 10
8
N/m
2
. The area of cross-section of the upper wire is 0.006 cm
2
and that of the lower wire is 0.003
cm . The mass m 1 = 10 kg, m 2 = 20 kg and the hanger is light. Find the maximum load that can be
put on the hanger without breaking a wire. Which wire will break first if the load is increased ?
(Take g = 10 m/s
2
)
Q 6. A steel wire and a copper wire of equal length and equal cross-sectional area are joined end to end
and the combination is subjected to a tension. Find the ratio of:
(a) the stresses developed in the two wires,
(b) the strains developed. (Y of steel =2 × 10
11
N/m
2
and T of copper = 1.3 × 10
11
N/m
2
)
Q 7. Calculate the approximate change in density of water in a lake at a depth of 400 m below the
surface. The density of water at the surface is 1030 kg/m
3
and bulk modulus of water is 2 ×
10
9
N/m
2
.
Q 8. A wire of length 3 m, diameter 0.4 mm and Young's modulus 8 × 10
10
N/m
2
is suspended from a
point and supports a heavy cylinder of volume 10
-3
m
3
at its lower end. Find the decrease in length
when the metal cylinder is immersed in a liquid of density 800 kg/m
3
.
Q 9. In taking a solid ball of rubber from the surface to the bottom of a lake of 180 m depth, reduction
in the volume of the ball is 0.1%. The density of water of the lake is 1 × 10
3
kg/m . Determine the
value of the bulk modulus of elasticity of rubber. (g = 9.8m/s
2
)
Q 10. A sphere of radius 10 cm and mass 25 kg is attached to the lower end of a steel wire of length 5 m
and diameter 4 mm which is suspended from the ceiling of a room. The point of support is 521 cm
above the floor. When the sphere is set swinging as a simple pendulum, its lowest point just grazes
the floor. Calculate the velocity of the ball at its lowest position. (Y steel =2 × 10
11
N/m
2
)
Q 11. A uniform ring of radius R and made up of a wire of cross-sectional radius r is rotated about its
axis with a frequency v. If density of the wire is p and Young's modulus is Y. Find the fractional
change in radius of the ring.
Q 12. A 6 kg weight is fastened to the end of a steel wire of unstretched length 60 cm. It is whirled in a
vertical circle and has an angular velocity of 2 rev's at the bottom of the circle. The area of cross-
section of the wire is 0.05 cm
2
. Calculate the elongation of the wire when the weight is at the
lowest point of the path. Young's modulus of steel =2 × 10
11
N/m
2
.
Q 13. A homogeneous block with a mass m hangs on three vertical wires of equal length arranged
symmetrically. Find the tension of the wires if the middle wire is of steel and the other two are of
copper. All the wires have the same cross-section. Consider the modulus of elasticity of steel to be
double than that of copper.
Q 14. A uniform copper bar of density length L, cross-sectional area S and Young's modulus Y is
moving horizontally on a frictionless surface with constant acceleration a0. Find :
(a) the stress at the centre of the wire, (b) total elongation of the wire.
Q 15. A 5 m long cylindrical steel wire with radius 2 × 10
-3
m is suspended vertically from a rigid
support and carries a bob of mass 100 kg at the other end. If the bob gets snapped, calculate the
change in temperature of the wire ignoring radiation losses. (Take g =10m/s
2
)
(For the steel wire : Young's modulus =2.1 × 10
11
N/m
2
; Density = 7860 kg/m
3
; Specific heat =
420.T/kg-°C).
Solutions
1.
= 1.9 × 10
-3
m = 1.9 mm
2. × 3 × 10
8
N/m
2
Page 3
EXERCISES
For JEE Main
Subjective Questions
Q 1. A cylindrical steel wire of 3 m length is to stretch no more than 0.2 cm when a tensile force of 400
N is applied to each end of the wire. What minimum diameter is required for the wire ?
Ysteel =2.1 × 10
11
N/m
2
Q 2. The elastic limit of a steel cable is 3.0 × 10
8
N/m
2
and the cross-section area is 4 cm
2
. Find the
maximum upward acceleration that can be given to a 900 kg elevator supported by the cable if the
stress is not to exceed one-third of the elastic limit.
Q 3. If the elastic limit of copper is 1.5 x 10
8
N/m
2
, determine the minimum diameter a copper wire can
have under a load of 10.0 kg, if its elastic limit is not to be exceeded.
Q 4. Find the increment in the length of a steel wire of length 5 m and radius 6 mm under its own
weight. Density of steel = 8000 kg/m
3
and Young's modulus of steel = 2 x 10
11
N/m
2
. What is the
energy stored in the wire ? (Take g = 9.8m/s
2
)
Q 5. Two wires shown in figure are made of the same material which has a breaking stress of 8 × 10
8
N/m
2
. The area of cross-section of the upper wire is 0.006 cm
2
and that of the lower wire is 0.003
cm . The mass m 1 = 10 kg, m 2 = 20 kg and the hanger is light. Find the maximum load that can be
put on the hanger without breaking a wire. Which wire will break first if the load is increased ?
(Take g = 10 m/s
2
)
Q 6. A steel wire and a copper wire of equal length and equal cross-sectional area are joined end to end
and the combination is subjected to a tension. Find the ratio of:
(a) the stresses developed in the two wires,
(b) the strains developed. (Y of steel =2 × 10
11
N/m
2
and T of copper = 1.3 × 10
11
N/m
2
)
Q 7. Calculate the approximate change in density of water in a lake at a depth of 400 m below the
surface. The density of water at the surface is 1030 kg/m
3
and bulk modulus of water is 2 ×
10
9
N/m
2
.
Q 8. A wire of length 3 m, diameter 0.4 mm and Young's modulus 8 × 10
10
N/m
2
is suspended from a
point and supports a heavy cylinder of volume 10
-3
m
3
at its lower end. Find the decrease in length
when the metal cylinder is immersed in a liquid of density 800 kg/m
3
.
Q 9. In taking a solid ball of rubber from the surface to the bottom of a lake of 180 m depth, reduction
in the volume of the ball is 0.1%. The density of water of the lake is 1 × 10
3
kg/m . Determine the
value of the bulk modulus of elasticity of rubber. (g = 9.8m/s
2
)
Q 10. A sphere of radius 10 cm and mass 25 kg is attached to the lower end of a steel wire of length 5 m
and diameter 4 mm which is suspended from the ceiling of a room. The point of support is 521 cm
above the floor. When the sphere is set swinging as a simple pendulum, its lowest point just grazes
the floor. Calculate the velocity of the ball at its lowest position. (Y steel =2 × 10
11
N/m
2
)
Q 11. A uniform ring of radius R and made up of a wire of cross-sectional radius r is rotated about its
axis with a frequency v. If density of the wire is p and Young's modulus is Y. Find the fractional
change in radius of the ring.
Q 12. A 6 kg weight is fastened to the end of a steel wire of unstretched length 60 cm. It is whirled in a
vertical circle and has an angular velocity of 2 rev's at the bottom of the circle. The area of cross-
section of the wire is 0.05 cm
2
. Calculate the elongation of the wire when the weight is at the
lowest point of the path. Young's modulus of steel =2 × 10
11
N/m
2
.
Q 13. A homogeneous block with a mass m hangs on three vertical wires of equal length arranged
symmetrically. Find the tension of the wires if the middle wire is of steel and the other two are of
copper. All the wires have the same cross-section. Consider the modulus of elasticity of steel to be
double than that of copper.
Q 14. A uniform copper bar of density length L, cross-sectional area S and Young's modulus Y is
moving horizontally on a frictionless surface with constant acceleration a0. Find :
(a) the stress at the centre of the wire, (b) total elongation of the wire.
Q 15. A 5 m long cylindrical steel wire with radius 2 × 10
-3
m is suspended vertically from a rigid
support and carries a bob of mass 100 kg at the other end. If the bob gets snapped, calculate the
change in temperature of the wire ignoring radiation losses. (Take g =10m/s
2
)
(For the steel wire : Young's modulus =2.1 × 10
11
N/m
2
; Density = 7860 kg/m
3
; Specific heat =
420.T/kg-°C).
Solutions
1.
= 1.9 × 10
-3
m = 1.9 mm
2. × 3 × 10
8
N/m
2
3.
4.
= 49 × 10
-6
m
5.
= 48 - 30 = 18 kg
So, lower wire will break if m > 14 kg. i.e., maximum load which can be put on hanger without
breaking wire is 14 kg
6. is same as both have same cross-section area and subjected under same tension.
7.
Page 4
EXERCISES
For JEE Main
Subjective Questions
Q 1. A cylindrical steel wire of 3 m length is to stretch no more than 0.2 cm when a tensile force of 400
N is applied to each end of the wire. What minimum diameter is required for the wire ?
Ysteel =2.1 × 10
11
N/m
2
Q 2. The elastic limit of a steel cable is 3.0 × 10
8
N/m
2
and the cross-section area is 4 cm
2
. Find the
maximum upward acceleration that can be given to a 900 kg elevator supported by the cable if the
stress is not to exceed one-third of the elastic limit.
Q 3. If the elastic limit of copper is 1.5 x 10
8
N/m
2
, determine the minimum diameter a copper wire can
have under a load of 10.0 kg, if its elastic limit is not to be exceeded.
Q 4. Find the increment in the length of a steel wire of length 5 m and radius 6 mm under its own
weight. Density of steel = 8000 kg/m
3
and Young's modulus of steel = 2 x 10
11
N/m
2
. What is the
energy stored in the wire ? (Take g = 9.8m/s
2
)
Q 5. Two wires shown in figure are made of the same material which has a breaking stress of 8 × 10
8
N/m
2
. The area of cross-section of the upper wire is 0.006 cm
2
and that of the lower wire is 0.003
cm . The mass m 1 = 10 kg, m 2 = 20 kg and the hanger is light. Find the maximum load that can be
put on the hanger without breaking a wire. Which wire will break first if the load is increased ?
(Take g = 10 m/s
2
)
Q 6. A steel wire and a copper wire of equal length and equal cross-sectional area are joined end to end
and the combination is subjected to a tension. Find the ratio of:
(a) the stresses developed in the two wires,
(b) the strains developed. (Y of steel =2 × 10
11
N/m
2
and T of copper = 1.3 × 10
11
N/m
2
)
Q 7. Calculate the approximate change in density of water in a lake at a depth of 400 m below the
surface. The density of water at the surface is 1030 kg/m
3
and bulk modulus of water is 2 ×
10
9
N/m
2
.
Q 8. A wire of length 3 m, diameter 0.4 mm and Young's modulus 8 × 10
10
N/m
2
is suspended from a
point and supports a heavy cylinder of volume 10
-3
m
3
at its lower end. Find the decrease in length
when the metal cylinder is immersed in a liquid of density 800 kg/m
3
.
Q 9. In taking a solid ball of rubber from the surface to the bottom of a lake of 180 m depth, reduction
in the volume of the ball is 0.1%. The density of water of the lake is 1 × 10
3
kg/m . Determine the
value of the bulk modulus of elasticity of rubber. (g = 9.8m/s
2
)
Q 10. A sphere of radius 10 cm and mass 25 kg is attached to the lower end of a steel wire of length 5 m
and diameter 4 mm which is suspended from the ceiling of a room. The point of support is 521 cm
above the floor. When the sphere is set swinging as a simple pendulum, its lowest point just grazes
the floor. Calculate the velocity of the ball at its lowest position. (Y steel =2 × 10
11
N/m
2
)
Q 11. A uniform ring of radius R and made up of a wire of cross-sectional radius r is rotated about its
axis with a frequency v. If density of the wire is p and Young's modulus is Y. Find the fractional
change in radius of the ring.
Q 12. A 6 kg weight is fastened to the end of a steel wire of unstretched length 60 cm. It is whirled in a
vertical circle and has an angular velocity of 2 rev's at the bottom of the circle. The area of cross-
section of the wire is 0.05 cm
2
. Calculate the elongation of the wire when the weight is at the
lowest point of the path. Young's modulus of steel =2 × 10
11
N/m
2
.
Q 13. A homogeneous block with a mass m hangs on three vertical wires of equal length arranged
symmetrically. Find the tension of the wires if the middle wire is of steel and the other two are of
copper. All the wires have the same cross-section. Consider the modulus of elasticity of steel to be
double than that of copper.
Q 14. A uniform copper bar of density length L, cross-sectional area S and Young's modulus Y is
moving horizontally on a frictionless surface with constant acceleration a0. Find :
(a) the stress at the centre of the wire, (b) total elongation of the wire.
Q 15. A 5 m long cylindrical steel wire with radius 2 × 10
-3
m is suspended vertically from a rigid
support and carries a bob of mass 100 kg at the other end. If the bob gets snapped, calculate the
change in temperature of the wire ignoring radiation losses. (Take g =10m/s
2
)
(For the steel wire : Young's modulus =2.1 × 10
11
N/m
2
; Density = 7860 kg/m
3
; Specific heat =
420.T/kg-°C).
Solutions
1.
= 1.9 × 10
-3
m = 1.9 mm
2. × 3 × 10
8
N/m
2
3.
4.
= 49 × 10
-6
m
5.
= 48 - 30 = 18 kg
So, lower wire will break if m > 14 kg. i.e., maximum load which can be put on hanger without
breaking wire is 14 kg
6. is same as both have same cross-section area and subjected under same tension.
7.
8.
= -2.39 × 10
-3
m
9.
= 1.76 × 10
9
N/m
2
10.
11.
sin ? ? ?
= 2 ? v
2
mR
l = 2 ?R
But m = (2 ?R)( ?r
2
)( ?)
Page 5
EXERCISES
For JEE Main
Subjective Questions
Q 1. A cylindrical steel wire of 3 m length is to stretch no more than 0.2 cm when a tensile force of 400
N is applied to each end of the wire. What minimum diameter is required for the wire ?
Ysteel =2.1 × 10
11
N/m
2
Q 2. The elastic limit of a steel cable is 3.0 × 10
8
N/m
2
and the cross-section area is 4 cm
2
. Find the
maximum upward acceleration that can be given to a 900 kg elevator supported by the cable if the
stress is not to exceed one-third of the elastic limit.
Q 3. If the elastic limit of copper is 1.5 x 10
8
N/m
2
, determine the minimum diameter a copper wire can
have under a load of 10.0 kg, if its elastic limit is not to be exceeded.
Q 4. Find the increment in the length of a steel wire of length 5 m and radius 6 mm under its own
weight. Density of steel = 8000 kg/m
3
and Young's modulus of steel = 2 x 10
11
N/m
2
. What is the
energy stored in the wire ? (Take g = 9.8m/s
2
)
Q 5. Two wires shown in figure are made of the same material which has a breaking stress of 8 × 10
8
N/m
2
. The area of cross-section of the upper wire is 0.006 cm
2
and that of the lower wire is 0.003
cm . The mass m 1 = 10 kg, m 2 = 20 kg and the hanger is light. Find the maximum load that can be
put on the hanger without breaking a wire. Which wire will break first if the load is increased ?
(Take g = 10 m/s
2
)
Q 6. A steel wire and a copper wire of equal length and equal cross-sectional area are joined end to end
and the combination is subjected to a tension. Find the ratio of:
(a) the stresses developed in the two wires,
(b) the strains developed. (Y of steel =2 × 10
11
N/m
2
and T of copper = 1.3 × 10
11
N/m
2
)
Q 7. Calculate the approximate change in density of water in a lake at a depth of 400 m below the
surface. The density of water at the surface is 1030 kg/m
3
and bulk modulus of water is 2 ×
10
9
N/m
2
.
Q 8. A wire of length 3 m, diameter 0.4 mm and Young's modulus 8 × 10
10
N/m
2
is suspended from a
point and supports a heavy cylinder of volume 10
-3
m
3
at its lower end. Find the decrease in length
when the metal cylinder is immersed in a liquid of density 800 kg/m
3
.
Q 9. In taking a solid ball of rubber from the surface to the bottom of a lake of 180 m depth, reduction
in the volume of the ball is 0.1%. The density of water of the lake is 1 × 10
3
kg/m . Determine the
value of the bulk modulus of elasticity of rubber. (g = 9.8m/s
2
)
Q 10. A sphere of radius 10 cm and mass 25 kg is attached to the lower end of a steel wire of length 5 m
and diameter 4 mm which is suspended from the ceiling of a room. The point of support is 521 cm
above the floor. When the sphere is set swinging as a simple pendulum, its lowest point just grazes
the floor. Calculate the velocity of the ball at its lowest position. (Y steel =2 × 10
11
N/m
2
)
Q 11. A uniform ring of radius R and made up of a wire of cross-sectional radius r is rotated about its
axis with a frequency v. If density of the wire is p and Young's modulus is Y. Find the fractional
change in radius of the ring.
Q 12. A 6 kg weight is fastened to the end of a steel wire of unstretched length 60 cm. It is whirled in a
vertical circle and has an angular velocity of 2 rev's at the bottom of the circle. The area of cross-
section of the wire is 0.05 cm
2
. Calculate the elongation of the wire when the weight is at the
lowest point of the path. Young's modulus of steel =2 × 10
11
N/m
2
.
Q 13. A homogeneous block with a mass m hangs on three vertical wires of equal length arranged
symmetrically. Find the tension of the wires if the middle wire is of steel and the other two are of
copper. All the wires have the same cross-section. Consider the modulus of elasticity of steel to be
double than that of copper.
Q 14. A uniform copper bar of density length L, cross-sectional area S and Young's modulus Y is
moving horizontally on a frictionless surface with constant acceleration a0. Find :
(a) the stress at the centre of the wire, (b) total elongation of the wire.
Q 15. A 5 m long cylindrical steel wire with radius 2 × 10
-3
m is suspended vertically from a rigid
support and carries a bob of mass 100 kg at the other end. If the bob gets snapped, calculate the
change in temperature of the wire ignoring radiation losses. (Take g =10m/s
2
)
(For the steel wire : Young's modulus =2.1 × 10
11
N/m
2
; Density = 7860 kg/m
3
; Specific heat =
420.T/kg-°C).
Solutions
1.
= 1.9 × 10
-3
m = 1.9 mm
2. × 3 × 10
8
N/m
2
3.
4.
= 49 × 10
-6
m
5.
= 48 - 30 = 18 kg
So, lower wire will break if m > 14 kg. i.e., maximum load which can be put on hanger without
breaking wire is 14 kg
6. is same as both have same cross-section area and subjected under same tension.
7.
8.
= -2.39 × 10
-3
m
9.
= 1.76 × 10
9
N/m
2
10.
11.
sin ? ? ?
= 2 ? v
2
mR
l = 2 ?R
But m = (2 ?R)( ?r
2
)( ?)
Substituting
the values we get,
12.
= 3.8 × 10
-4
m
13. 2Tc + T s = mg ...(i)
Solving these two equations we get,
14.
(a) At centre :
? Stress =
(b) At distance x from end B :
Tx =m xa0 =(xs ?)a0
15. Energy stored in stretched wire = ms ?Q
Objective Questions Single Correct Option
Q 1. The bulk modulus for an incompressible liquid is
(a) zero (b) unity (c) infinity (d) between 0 and 1
Q 2. The Young's modulus of a wire of length (L) and radius (r) is 7. If the length is reduced to
L
2
and
radius
r
2
,
then its Young's modulus will be
(a)
Y
2
(b) 7 (c) 27 (d) 47
Q 3. The maximum load that a wire can sustain is W. If the wire is cut to half its value, the maximum
load it can sustain is
(a) W (b)
W
2
(c)
W
4
(d) 2W
Q 4. Identify the case when an elastic metal rod does not undergo elongation
Read More
FAQs on DC Pandey Solutions (JEE Main): Elasticity - DC Pandey Solutions for JEE Physics
| 1. What is elasticity in the context of JEE Main Physics? |  |
Ans. In the context of JEE Main Physics, elasticity refers to the property of a material to regain its original shape and size after being deformed by an external force. It is a measure of how much a material can stretch or compress under the influence of a force.
| 2. How is elasticity related to the JEE Main exam? | |
Ans. Elasticity is an important topic in the JEE Main Physics syllabus. Questions related to elasticity often appear in the exam, testing the understanding of concepts such as stress, strain, Young's modulus, and Hooke's law. It is essential for JEE Main aspirants to have a clear understanding of elasticity to solve these questions accurately.
| 3. What is Young's modulus? | |
Ans. Young's modulus, denoted by the symbol 'Y', is a measure of the stiffness or rigidity of a material. It is defined as the ratio of stress (force per unit area) to strain (deformation per unit length) in a material within the elastic limit. Young's modulus is a fundamental concept in elasticity and is used to determine the extent of deformation a material undergoes under the application of a force.
| 4. How can I calculate the strain in a material? | |
Ans. Strain is calculated by dividing the change in length of a material by its original length. Mathematically, strain (ε) is given by the formula: ε = (ΔL / L), where ΔL represents the change in length and L represents the original length of the material. Strain is a dimensionless quantity and is often expressed as a decimal or a percentage.
| 5. What is Hooke's law? | |
Ans. Hooke's law states that the extension produced in a material is directly proportional to the applied force, provided the elastic limit of the material is not exceeded. Mathematically, Hooke's law can be represented as F = kx, where F is the applied force, k is the spring constant (a measure of the stiffness of the material), and x is the extension or compression of the material. Hooke's law is applicable to materials within their elastic limit, and it helps in understanding the behavior of materials under the influence of external forces.
Related Exams
About this Document
|
4.70/5 Rating |
|
Dec 22, 2024 Last updated |
Document Description: DC Pandey Solutions (JEE Main): Elasticity for JEE 2024 is part of DC Pandey Solutions for JEE Physics preparation.
The notes and questions for DC Pandey Solutions (JEE Main): Elasticity have been prepared according to the JEE exam syllabus. Information about DC Pandey Solutions (JEE Main): Elasticity covers topics
like and DC Pandey Solutions (JEE Main): Elasticity Example, for JEE 2024 Exam. Find important definitions, questions, notes, meanings, examples, exercises and tests below for DC Pandey Solutions (JEE Main): Elasticity.
Introduction of DC Pandey Solutions (JEE Main): Elasticity in English is available as part of our DC Pandey Solutions for JEE Physics
for JEE & DC Pandey Solutions (JEE Main): Elasticity in Hindi for DC Pandey Solutions for JEE Physics course.
Download more important topics related with notes, lectures and mock test series for JEE
Exam by signing up for free. JEE: DC Pandey Solutions (JEE Main): Elasticity | DC Pandey Solutions for JEE Physics
Description
Full syllabus notes, lecture & questions for DC Pandey Solutions (JEE Main): Elasticity | DC Pandey Solutions for JEE Physics - JEE | Plus excerises question with solution to help you revise complete syllabus for DC Pandey Solutions for JEE Physics | Best notes, free PDF download
Information about DC Pandey Solutions (JEE Main): Elasticity
In this doc you can find the meaning of DC Pandey Solutions (JEE Main): Elasticity defined & explained in the simplest way possible. Besides explaining types of
DC Pandey Solutions (JEE Main): Elasticity theory, EduRev gives you an ample number of questions to practice DC Pandey Solutions (JEE Main): Elasticity tests, examples and also practice JEE
tests
|
Explore Courses for JEE exam
|
|
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
Related Searches
Summary
,DC Pandey Solutions (JEE Main): Elasticity | DC Pandey Solutions for JEE Physics
,ppt
,Exam
,video lectures
,past year papers
,Important questions
,Sample Paper
,Extra Questions
,MCQs
,study material
,Previous Year Questions with Solutions
,DC Pandey Solutions (JEE Main): Elasticity | DC Pandey Solutions for JEE Physics
,Viva Questions
,DC Pandey Solutions (JEE Main): Elasticity | DC Pandey Solutions for JEE Physics
,Semester Notes
,Objective type Questions
,mock tests for examination
,Free
,practice quizzes
,shortcuts and tricks
;
Additional Information about DC Pandey Solutions (JEE Main): Elasticity for JEE Preparation
DC Pandey Solutions (JEE Main): Elasticity Free PDF Download
The DC Pandey Solutions (JEE Main): Elasticity is an invaluable resource that delves deep into the core of the JEE exam.
These study notes are curated by experts and cover all the essential topics and concepts, making your preparation more efficient and effective.
With the help of these notes, you can grasp complex subjects quickly, revise important points easily,
and reinforce your understanding of key concepts. The study notes are presented in a concise and easy-to-understand manner,
allowing you to optimize your learning process. Whether you're looking for best-recommended books, sample papers, study material,
or toppers' notes, this PDF has got you covered. Download the DC Pandey Solutions (JEE Main): Elasticity now and kickstart your journey towards success in the JEE exam.
Importance of DC Pandey Solutions (JEE Main): Elasticity
The importance of DC Pandey Solutions (JEE Main): Elasticity cannot be overstated, especially for JEE aspirants.
This document holds the key to success in the JEE exam.
It offers a detailed understanding of the concept, providing invaluable insights into the topic.
By knowing the concepts well in advance, students can plan their preparation effectively.
Utilize this indispensable guide for a well-rounded preparation and achieve your desired results.
DC Pandey Solutions (JEE Main): Elasticity Notes
DC Pandey Solutions (JEE Main): Elasticity Notes offer in-depth insights into the specific topic to help you master it with ease.
This comprehensive document covers all aspects related to DC Pandey Solutions (JEE Main): Elasticity.
It includes detailed information about the exam syllabus, recommended books, and study materials for a well-rounded preparation.
Practice papers and question papers enable you to assess your progress effectively.
Additionally, the paper analysis provides valuable tips for tackling the exam strategically.
Access to Toppers' notes gives you an edge in understanding complex concepts.
Whether you're a beginner or aiming for advanced proficiency, DC Pandey Solutions (JEE Main): Elasticity Notes on EduRev are your ultimate resource for success.
DC Pandey Solutions (JEE Main): Elasticity JEE Questions
The "DC Pandey Solutions (JEE Main): Elasticity JEE Questions" guide is a valuable resource for all aspiring students preparing for the
JEE exam. It focuses on providing a wide range of practice questions to help students gauge
their understanding of the exam topics. These questions cover the entire syllabus, ensuring comprehensive preparation.
The guide includes previous years' question papers for students to familiarize themselves with the exam's format and difficulty level.
Additionally, it offers subject-specific question banks, allowing students to focus on weak areas and improve their performance.
Study DC Pandey Solutions (JEE Main): Elasticity on the App
Students of JEE can study DC Pandey Solutions (JEE Main): Elasticity alongwith tests & analysis from the EduRev app,
which will help them while preparing for their exam. Apart from the DC Pandey Solutions (JEE Main): Elasticity,
students can also utilize the EduRev App for other study materials such as previous year question papers, syllabus, important questions, etc.
The EduRev App will make your learning easier as you can access it from anywhere you want.
The content of DC Pandey Solutions (JEE Main): Elasticity is prepared as per the latest JEE syllabus.
|
© EduRev
|
Education Revolution
|
|
Signup to see your scores
go up within 7 days!
Access 1000+ FREE Docs, Videos and Tests
Takes less than 10 seconds to signup