Digital Counters - Digital Electronics, CSIR-NET Physical Sciences | Physics for IIT JAM, UGC - NET, CSIR NET PDF Download
Counter is a sequential circuit. A digital circuit which is used for a counting pulses is known counter. Counter is the widest application of flip-flops. It is a group of flip-flops with a clock signal applied. Counters are of two types.
Asynchronous or ripple counters.
Synchronous counters.
Asynchronous or ripple counters
The logic diagram of a 2-bit ripple up counter is shown in figure. The toggle (T) flip-flop are being used. But we can use the JK flip-flop also with J and K connected permanently to logic 1. External clock is applied to the clock input of flip-flop A and QA output is applied to the clock input of the next flip-flop i.e. FF-B.
Logical Diagram
Operation
S.N. | Condition | Operation |
|---|---|---|
1 | Initially let both the FFs be in the reset state | QBQA = 00 initially |
2 | After 1st negative clock edge | As soon as the first negative clock edge is applied, FF-A will toggle and QA will be equal to 1. QA is connected to clock input of FF-B. Since QA has changed from 0 to 1, it is treated as the positive clock edge by FF-B. There is no change in QB because FF-B is a negative edge triggered FF. QBQA = 01 after the first clock pulse. |
3 | After 2nd negative clock edge | On the arrival of second negative clock edge, FF-A toggles again and QA = 0. The change in QA acts as a negative clock edge for FF-B. So it will also toggle, and QBwill be 1. QBQA = 10 after the second clock pulse. |
4 | After 3rd negative clock edge | On the arrival of 3rd negative clock edge, FF-A toggles again and QA become 1 from 0. Since this is a positive going change, FF-B does not respond to it and remains inactive. So QB does not change and continues to be equal to 1. QBQA = 11 after the third clock pulse. |
5 | After 4th negative clock edge | On the arrival of 4th negative clock edge, FF-A toggles again and QA becomes 1 from 0. This negative change in QAacts as clock pulse for FF-B. Hence it toggles to change QBfrom 1 to 0. QBQA = 00 after the fourth clock pulse. |
Truth Table
Synchronous counters
If the "clock" pulses are applied to all the flip-flops in a counter simultaneously, then such a counter is called as synchronous counter.
2-bit Synchronous up counter
The JA and KA inputs of FF-A are tied to logic 1. So FF-A will work as a toggle flip-flop. The JB and KB inputs are connected to QA.
Logical Diagram
Operation
S.N. | Condition | Operation |
|---|---|---|
1 | Initially let both the FFs be in the reset state | QBQA = 00 initially. |
2 | After 1st negative clock edge | As soon as the first negative clock edge is applied, FF-A will toggle and QA will change from 0 to 1. But at the instant of application of negative clock edge, QA , JB = KB = 0. Hence FF-B will not change its state. So QB will remain 0. QBQA = 01 after the first clock pulse. |
3 | After 2nd negative clock edge | On the arrival of second negative clock edge, FF-A toggles again and QA changes from 1 to 0. But at this instant QA was 1. So JB = KB= 1 and FF-B will toggle. Hence QB changes from 0 to 1. QBQA = 10 after the second clock pulse. |
4 | After 3rd negative clock edge | On application of the third falling clock edge, FF-A will toggle from 0 to 1 but there is no change of state for FF-B. QBQA = 11 after the third clock pulse. |
5 | After 4th negative clock edge | On application of the next clock pulse, QA will change from 1 to 0 as QB will also change from 1 to 0. QBQA = 00 after the fourth clock pulse. |
Classification of counters
Depending on the way in which the counting progresses, the synchronous or asynchronous counters are classified as follows −
Up counters
Down counters
Up/Down counters
UP/DOWN Counter
Up counter and down counter is combined together to obtain an UP/DOWN counter. A mode control (M) input is also provided to select either up or down mode. A combinational circuit is required to be designed and used between each pair of flip-flop in order to achieve the up/down operation.
Type of up/down counters
UP/DOWN ripple counters
UP/DOWN synchronous counter
UP/DOWN Ripple Counters
In the UP/DOWN ripple counter all the FFs operate in the toggle mode. So either T flip-flops or JK flip-flops are to be used. The LSB flip-flop receives clock directly. But the clock to every other FF is obtained from (Q = Q bar) output of the previous FF.
UP counting mode (M=0) − The Q output of the preceding FF is connected to the clock of the next stage if up counting is to be achieved. For this mode, the mode select input M is at logic 0 (M=0).
DOWN counting mode (M=1) − If M = 1, then the Q bar output of the preceding FF is connected to the next FF. This will operate the counter in the counting mode.
Example
3-bit binary up/down ripple counter.
3-bit − hence three FFs are required.
UP/DOWN − So a mode control input is essential.
For a ripple up counter, the Q output of preceding FF is connected to the clock input of the next one.
For a ripple up counter, the Q output of preceding FF is connected to the clock input of the next one.
For a ripple down counter, the Q bar output of preceding FF is connected to the clock input of the next one.
Let the selection of Q and Q bar output of the preceding FF be controlled by the mode control input M such that, If M = 0, UP counting. So connect Q to CLK. If M = 1, DOWN counting. So connect Q bar to CLK.
Block Diagram
Truth Table
Operation
S.N. | Condition | Operation |
|---|---|---|
1 | Case 1 − With M = 0 (Up counting mode) | If M = 0 and M bar = 1, then the AND gates 1 and 3 in fig. will be enabled whereas the AND gates 2 and 4 will be disabled. Hence QA gets connected to the clock input of FF-B and QBgets connected to the clock input of FF-C. These connections are same as those for the normal up counter. Thus with M = 0 the circuit work as an up counter. |
2 | Case 2: With M = 1 (Down counting mode) | If M = 1, then AND gates 2 and 4 in fig. are enabled whereas the AND gates 1 and 3 are disabled. Hence QA bar gets connected to the clock input of FF-B and QB bar gets connected to the clock input of FF-C. These connections will produce a down counter. Thus with M = 1 the circuit works as a down counter. |
Modulus Counter (MOD-N Counter)
The 2-bit ripple counter is called as MOD-4 counter and 3-bit ripple counter is called as MOD-8 counter. So in general, an n-bit ripple counter is called as modulo-N counter. Where, MOD number = 2n.
Type of modulus
2-bit up or down (MOD-4)
3-bit up or down (MOD-8)
4-bit up or down (MOD-16)
Application of counters
Frequency counters
Digital clock
Time measurement
A to D converter
Frequency divider circuits
Digital triangular wave generator.
FAQs on Digital Counters - Digital Electronics, CSIR-NET Physical Sciences - Physics for IIT JAM, UGC - NET, CSIR NET
| 1. What is a digital counter in digital electronics? |  |
| 2. How does a digital counter work? | |
| 3. What are the different types of digital counters? | |
| 4. How can digital counters be used in digital electronics? | |
| 5. What are the advantages of digital counters? | |
|
4.74/5 Rating |
|
Dec 26, 2024 Last updated |
|
Explore Courses for Physics exam
|
|
Objective type Questions
,Free
,Summary
,CSIR-NET Physical Sciences | Physics for IIT JAM
,Digital Counters - Digital Electronics
,practice quizzes
,Extra Questions
,MCQs
,shortcuts and tricks
,CSIR NET
,Digital Counters - Digital Electronics
,CSIR NET
,video lectures
,mock tests for examination
,UGC - NET
,CSIR NET
,Sample Paper
,Viva Questions
,UGC - NET
,Exam
,UGC - NET
,past year papers
,Important questions
,study material
,Previous Year Questions with Solutions
,CSIR-NET Physical Sciences | Physics for IIT JAM
,ppt
,CSIR-NET Physical Sciences | Physics for IIT JAM
,Semester Notes
,Digital Counters - Digital Electronics
;
Digital Counters - Digital Electronics, CSIR-NET Physical Sciences Free PDF Download
Importance of Digital Counters - Digital Electronics, CSIR-NET Physical Sciences
Digital Counters - Digital Electronics, CSIR-NET Physical Sciences Notes
Digital Counters - Digital Electronics, CSIR-NET Physical Sciences Physics Questions
Study Digital Counters - Digital Electronics, CSIR-NET Physical Sciences on the App
|
© EduRev
|
Education Revolution
|
|
