Chemical Engineering Exam  >  Chemical Engineering Notes  >  Mass Transfer  >  Determination Of The Stripping Section Operating Line (SOL)

Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering PDF Download

Determination of the stripping section operating line (SOL): 
The stripping section operating line (SOL) can be obtained from the ROL and qline without doing any material balance. The SOL can be drawn by connecting point xB on the diagonal to the point of intersection between the ROL and q-line. The SOL will change if q-line is changed at fixed ROL. The change of SOL with different q-lines for a given ROL at constant R and xD is shown in Figure 5.16.


Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering
Figure 5.16: Stripping section operating line with different q-lines 

The stripping section operating line can be derived from the material balance around the stripping section of the distillation column. The stripping section of a distillation column is shown in Figure 5.17. The reboiled vapor is in equilibrium with bottoms liquid which is leaving the column.
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering
Figure 5.17: Schematic of the stripping section

Consider the constant molal overflow in the column. Thus L'm = L'm+1 = .... = L' = constant and V'm = V'm+1 = ..... = V' = constant.
Overall material balance gives
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering                            (5.29)
More volatile component balance gives:
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering               (5.30)
Substituting and re-arranging the Equation (5.30) yields
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering       (5.31)
Dropping the subscripts "m+1" and "m" it becomes:
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering              (5.32)
Substituting V' = L' – B from Equation (5.29), the Equation (5.32) can be written as:
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering           (5.33)
The Equation (5.33) is called the stripping operating line (SOL) which is a straight line with slope ( L' / L' - B) and intercept Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering When x = xB , y = xB, the SOL passes through (xB, xB ) on the 45o diagonal line.

Determination of number of theoretical stage 
Suppose a column is to be designed for the separation of a binary mixture where the feed has a concentration of xF (mole fraction) of the more volatile component and a distillate having a concentration of xD of the more volatile component whereas the bottoms having a desired concentration of xB. Once the three lines (ROL, SOL and q-line) are drawn, the number of theoretical stages required for a given separation is then the number of triangles that can be drawn between these operating lines and the equilibrium curve. The last triangle on the diagram represents the reboiler. A typical representation is given in Figure 5.18.


Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering
Figure 5.18: A typical representation of identifying number of theoretical stages

Reflux Ratio, R 
The separation efficiency by distillation depends on the reflux ratio. For a given separation (i.e. constant xD and xB) from a given feed condition (xand q), higher reflux ratio (R) results in lesser number of required theoretical trays (N) and vice versa. So there is an inverse relationship between the reflux ratio and the number of theoretical stages. At a specified distillate concentration, xD, when R changes, the slope and intercept of the ROL changes (Equation (5.19)). From the Equation (5.19), when R increases (with xD constant), the slope of ROL becomes steeper, i.e. (R/R+1) and the intercept (xD/R+1) decreases. The ROL therefore rotates around the point (xD, xD). The reflux ratio may be any value between a minimum value and an infinite value. The limit is the minimum reflux ratio (result in infinite stages) and the total reflux or infinite reflux ratio (result in minimum stages). With xD constant, as R decreases, the slope (R/R+1) of ROL (Equation (5.19)) decreases, while its intercept (xD/R+1) increases and rotates upwards around (xD, xD) as shown in Figure 5.19. The ROL moves closer to the equilibrium curve as R decreases until point Q is reached. Point Q is the point of intersection between the q-line and the equilibrium curve.


Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering
Figure 5.19: Representation of minimum reflux rtio

At this point of intersection the driving force for mass transfer is zero. This is also called as Pinch Point. At this point separation is not possible. The R cannot be reduced beyond this point. The value of R at this point is known as the minimum reflux ratio and is denoted by Rmin. For non-ideal mixture it is quite common to exhibit inflections in their equilibrium curves as shown in Figure 5.20 (a, b). In those cases, the operating lines where it becomes tangent to the equilibrium curve (called tangent pinch) is the condition for minimum reflux. The ROL cannot move beyond point P, e.g. to point K. The condition for zero driving force first occurs at point P, before point K which is the intersection point between the qline and equilibrium curve. Similarly it is the condition SOL also. At the total reflux ratio, the ROL and SOL coincide with the 45 degree diagonal line. At this condition, total number of triangles formed with the equilibrium curve is equal minimum number of theoretical stages. The reflux ratio will be infinite.


Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering
Figure 5.20 (a): Representation of minimum reflux ratio for non-ideal mixture  

Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering
Figure 5.20 (b): Representation of minimum reflux ratio for non-ideal mixture

Tray Efficiency 
For the analysis of theoretical stage required for the distillation, it is assumed that the the vapor leaving each tray is in equilibrium with the liquid leaving the same tray and the trays are operating at 100% efficiency. In practice, the trays are not perfect. There are deviations from ideal conditions. The equilibrium with temperature is sometimes reasonable for exothermic chemical reaction but the equilibrium with respect to mass transfer is not often valid. The deviation from the ideal condition is due to: (1) Insufficient time of contact (2) Insufficient degree of mixing. To achieve the same degree of desired separation, more trays will have to be added to compensate for the lack of perfect separability. The concept of tray efficiency may be used to adjust the the actual number of trays required.

Overall Efficiency 
The overall tray efficiency, EO is defined as:
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering       (5.34)
It is applied for the whole column. Every tray is assumed to have the same efficiency. The overall efficiency depends on the (i) geometry and design of the contacting trays, (ii) flow rates and flow paths of vapor and liquid streams, (iii) Compositions and properties of vapor and liquid streams (Treybal, 1981; Seader and Henley, 1998). The overall efficiency can be calculated from the following correlations:
The Drickamer-Bradford empirical correlation:
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering              (5.35)
The corrrelation is valid for hydrocarbon mixtures in the range of 342 K < T < 488.5 K, 1 atm < P < 25 atm and 0.066 < � < 0.355 cP
The O'Connell correlation:
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering                   (5.36)

Murphree Efficiency 
The efficiency of the tray can also be calculated based on semi-theoretical models which can be interpreted by the Murphree Tray Efficiency EM. In this case it is assumed that the vapor and liquid between trays are well-mixed and have uniform composition. It is defined for each tray according to the separation achieved on each tray based on either the liquid phase or the vapor phase. For a given component, it can be expressed as:
Based on vapor phase:
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering                        (5.37)
Based on liquid phase:
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering                     (5.38)


Example problem 5.2: 
A liquid mixture of benzene toluene is being distilled in a fractionating column at 101.3 k Pa pressure. The feed of 100 kmole/h is liquid and it contains 45 mole% benzene (A) and 55 mole% toluene (B) and enters at 327.6 K. A distillate containing 95 mole% benzene and 5 mole% toluene and a bottoms containing 10 mole% benzene and 90 mole% toluene are to be obtained. The amount of liquid is fed back to the column at the top is 4 times the distillate product. The average heat capacity of the feed is 159 KJ/kg mole. K and the average latent heat 32099 kJ/kg moles.
Calculate
i. The kg moles per hour distillate, kg mole per hour bottoms
ii. No. of theoretical stages at the operating reflux.
iii. The minimum no. of theoretical stages required at total reflux
iv. If the actual no. of stage is 10, what is the overall efficiency increased at operating condition compared to the condition of total reflux?
The equilibrium data:
Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering

Solution 5.2: 
F = D + B
100 = D + B
F xF = D xD + B xB
Therefore, D = 41.2 kg mole/h, B = 58.8 kg mole/h
y = [R/(R+1)] x + xD/(R+1) = 0.8 x +0.190
q = 1+ cpL (TB-TF)/Latent heat of vaporization
TB = 366.7 K from boiling point of feed, TF = 327.6 K ( inlet feed temp)
Therefore q = 1.195
Slope of q line = 6.12
From the graph (Figure E1), Total no of theoretical stages is 8 at operating reflux
(Red color)
From the graph (Figure E1), Total no of theoretical stages is 6 at total reflux
(Black color)
Overall efficiency at operating conditions: Eo (Operating) = No of ideal stage/ No of actual trays = 7.9/10 = 0.79
Overall efficiency at total reflux conditions: Eo (total relux) = No of ideal stage/ No of actual trays = 5.9/10=0.59
Overall efficiency increased: 0.79-0.59 = 0.20

Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering
Figure E1: Graph representing the example problem 5.2.

The document Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering is a part of the Chemical Engineering Course Mass Transfer.
All you need of Chemical Engineering at this link: Chemical Engineering
29 videos|45 docs|44 tests

FAQs on Determination Of The Stripping Section Operating Line (SOL) - Mass Transfer - Chemical Engineering

1. What is the purpose of the Stripping Section Operating Line (SOL) in chemical engineering?
Ans. The Stripping Section Operating Line (SOL) is used to determine the relationship between the liquid and vapor compositions in a stripping column. It helps engineers understand and optimize the separation process by providing insights into the efficiency and performance of the column.
2. How is the Stripping Section Operating Line (SOL) determined?
Ans. The Stripping Section Operating Line (SOL) is determined through a combination of theoretical calculations and experimental data. Theoretical methods such as the McCabe-Thiele method or graphical methods can be used to estimate the SOL, while experimental data from pilot plants or actual industrial columns can be used to validate and refine the calculations.
3. What are the factors that can affect the shape and slope of the Stripping Section Operating Line (SOL)?
Ans. Several factors can influence the shape and slope of the Stripping Section Operating Line (SOL). These include the physical properties of the components being separated, the operating conditions of the column (such as temperature and pressure), the column design, and the presence of any entrainment or foaming in the column. Understanding these factors is crucial for optimizing the column's performance.
4. How does the Stripping Section Operating Line (SOL) impact the efficiency of a stripping column?
Ans. The Stripping Section Operating Line (SOL) has a direct impact on the efficiency of a stripping column. By analyzing the SOL, engineers can identify potential issues such as excessive liquid entrainment or poor vapor-liquid contact, which can reduce the column's efficiency. Adjusting the operating conditions or column design based on the SOL analysis can help improve the separation efficiency and reduce energy consumption.
5. Can the Stripping Section Operating Line (SOL) be used for other types of separation processes apart from stripping?
Ans. Yes, the principles and concepts of the Stripping Section Operating Line (SOL) can be applied to other types of separation processes as well. While the SOL is primarily used for stripping columns, similar operating lines can be determined for absorption columns, distillation columns, and other separation units. The SOL analysis provides valuable insights into the behavior of these processes and helps engineers optimize their performance.
29 videos|45 docs|44 tests
Download as PDF
Explore Courses for Chemical Engineering exam
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
10M+ students study on EduRev
Related Searches

mock tests for examination

,

Extra Questions

,

Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering

,

Objective type Questions

,

shortcuts and tricks

,

Summary

,

past year papers

,

study material

,

Previous Year Questions with Solutions

,

Viva Questions

,

Free

,

Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering

,

ppt

,

practice quizzes

,

Semester Notes

,

video lectures

,

pdf

,

Important questions

,

Exam

,

Determination Of The Stripping Section Operating Line (SOL) | Mass Transfer - Chemical Engineering

,

Sample Paper

,

MCQs

;