Electrical Engineering (EE) Exam  >  Electrical Engineering (EE) Notes  >  Analog and Digital Electronics  >  Thermal Runaway & Thermal Stability

Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE) PDF Download

THERMAL RUNAWAY:

            The collector current for the CE circuit is given by IC = βIB+(1+β)ICO . The three variables in the equation, β, IB, and ICO increase with rise in temperature. In particular, the reverse saturation current or leakage current ICO changes greatly with temperature. Specifically, it doubles for every 10oC rise in temperature. The collector current Icauses the collector base junction temperature to rise which in turn, increase ICO, as a result IC will increase still further, which will further increase the temperature at the collector base junction. This process will become cumulative at the collector base junction leading to “thermal runaway”. Consequently, the ratings of the transistor are exceeded which may destroy the transistor itself.


            The collector is made larger in size than the emitter in order to facilitate the heat dissipation at the collector junction. However if the circuit is designed such that the base current Iis made to decrease automatically with rise in temperature, then the decrease in βIB will compensate for increase in the (1+β)ICO, keeping IC almost constant.


THERMAL RESISTANCE

            Consider transistor used in a circuit where the ambient temperature of the air around the transistor is TAoC and the temperature of the collector-base junction of the transistor is TJoC.

Due to heating within the transistor, TJ is higher than TA. As the temperature difference TJ- TA is greater, the power dissipated in the transistor, PD will be greater, i.e, 

(TJ- TA) ∝ PD


The equation can be written as TJ- T=Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)PD, where Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)is the constant of proportionality and is called the Thermal resistance. Rearranging the above equationThermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)= (TJ- TA) /PD. Hence Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE) is measured in oC/W which may be as small as 0.2 oC/W for a high power transistor that has an efficient heat sink of up to 1000oC/W for small signal, low power transistor which have no cooling provision.


            As Θ represents total thermal resistance from a transistor junction to the ambient temperature, it is referred to as ΘJ-A.  However, for power transistors, thermal resistance is given as ΘJ-C.

            The amount of resistance from junction to ambience is considered to consist of 2 parts.

ΘJ-A = ΘJ-C - ΘC-A.

which indicates that the heat dissipated in the junction must make its way to the surrounding air through two series paths from junction to case and from case to air. Hence the power dissipated is given as-

PD = (TJ- TA) / Θ J-A 


=(TJ- TA )/ Θ J-C + Θ C-A)


ΘJ-C is determined by the type of manufacturer of the transistor and how it is located in the case, but ΘC-A is determined by the surface area of the case or flange and its contact with air. If the effective surface area of the transistor case could be increased, the resistance to heat flows could be increased ΘC-A, could be decreased. This can be achieved by the use of a heat sink.

            The heat sink is a relatively large, finned, usually black metallic heat conducting device in close contact with transistor case or flange. Many versions of heat sink exist depending upon the shape and size of the transistor. Larger the heat sink smaller is the thermal resistance ΘHS-A.

This thermal resistance is not added to ΘC-A in series, but is instead in parallel with it and if ΘHS-A is much less than ΘC-A, then ΘC-A will be reduced significantly, thereby improving the dissipation capability of the transistor. Thus

Θ J-AJ-C + Θ C-A|| ΘHS-A.


 

4.8 CONDITION FOR THERMAL STABILITY:

                For preventing thermal runaway, the required condition is the rate at which the heat is released at the collector junction should not exceed the rate at which the heat can be dissipated under steady state conditions. Hence the condition to be satisfied to avoid thermal runaway is given by-

Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)

If the circuit is properly designed, then the transistor cannot runaway below a specified ambient temperature  or even under any condition.

                In the self biased circuit the transistor is biased in the active region. The power generated at the junction without any signal is

Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)

Let us assume that the quiescent collector and the emitter currents are equal. Then

Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)


The condition to prevent thermal runaway can be written as

Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)

As Θ and  Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE) are positive, Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)should be negative in order to satisfy the above condition.


Differentiating  equation  (1) w.r.t  Iwe get


Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)

Hence to avoid thermal runaway it is necessary that

Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)

SinceVCE=VCC-IC(RE+RC) then eq (4) implies that VCE<VCC/2. If the inequality of eq (4) is not satisfied and VCE<VCC/2, then from eq(3), Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE) is positive., and the corresponding eq(2) should be satisfied. Other wise thermal runaway will occur.

The document Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE) is a part of the Electrical Engineering (EE) Course Analog and Digital Electronics.
All you need of Electrical Engineering (EE) at this link: Electrical Engineering (EE)
137 videos|143 docs|71 tests

Top Courses for Electrical Engineering (EE)

FAQs on Thermal Runaway & Thermal Stability - Analog and Digital Electronics - Electrical Engineering (EE)

1. What is thermal runaway?
Ans. Thermal runaway refers to a situation where the temperature of a system increases uncontrollably due to a positive feedback loop. It occurs when the heat generated within a system exceeds the capacity of the system to dissipate it, leading to a rapid increase in temperature.
2. How does thermal runaway occur?
Ans. Thermal runaway can occur due to various factors, such as a malfunctioning cooling system, excessive power input, or a failure in the temperature regulation mechanism. When the heat generated exceeds the system's ability to dissipate it, the temperature starts to rise rapidly, leading to thermal runaway.
3. What are the dangers of thermal runaway?
Ans. Thermal runaway can pose serious risks, such as the overheating and possible destruction of electronic components, fires, and even explosions. It can also lead to the release of toxic gases or the formation of hazardous byproducts, depending on the materials involved.
4. How can thermal runaway be prevented?
Ans. Preventing thermal runaway involves implementing measures to control and dissipate heat effectively. This can be achieved by ensuring proper ventilation and cooling systems, monitoring temperature levels, and employing safety measures such as thermal cutoff switches or alarms. Regular maintenance and inspection of the system also play a crucial role in preventing thermal runaway.
5. What is thermal stability?
Ans. Thermal stability refers to the ability of a system or material to maintain a relatively constant temperature under varying conditions. It indicates the system's resistance to thermal runaway and its capacity to dissipate heat efficiently, preventing temperature fluctuations that could lead to instability or damage. Achieving thermal stability often involves the use of thermal management techniques and appropriate design considerations.
137 videos|143 docs|71 tests
Download as PDF
Explore Courses for Electrical Engineering (EE) exam

Top Courses for Electrical Engineering (EE)

Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
10M+ students study on EduRev
Related Searches

mock tests for examination

,

pdf

,

Previous Year Questions with Solutions

,

Objective type Questions

,

practice quizzes

,

Exam

,

video lectures

,

Summary

,

Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)

,

Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)

,

Semester Notes

,

Extra Questions

,

shortcuts and tricks

,

Important questions

,

Thermal Runaway & Thermal Stability | Analog and Digital Electronics - Electrical Engineering (EE)

,

Viva Questions

,

study material

,

ppt

,

Free

,

past year papers

,

MCQs

,

Sample Paper

;