Fluid Mechanics, Strength Of Materials - 2 - Mechanical Engineering MCQ
20 Questions MCQ Test - Fluid Mechanics, Strength Of Materials - 2
The specific speed of a turbine is defined as the speed of a unit of such a size that it
What is the condition for maximum transmission of power through a nozzle at the end of a long pipe?
| 1 Crore+ students have signed up on EduRev. Have you? Download the App |
Which one of the following velocity fields represents a possible fluid flow?
Two long columns C1 and C2 are made of the same material. Column C1 has both the ends hinged while column C2 has one end hinged and the other end fixed. What is the ratio of the critical load for C1 to that for C2 according to Euler’s formula?
From a cicular plate of diameter D,whose center is C, another cicular plate of diameter AC is cut ,removed and kept over CB,The thickness of the plate is uniform. The shift of the centroid due to this will be
A cantilever is subjected to a uniformly distributed load W over its whole length L and a concentrated upward force W at its free end. The deflection of the free end is
The deformation of the bar under its own weight as compared to that when subjected to a direct axial load equal to its own weight will be
A thin cylindrical shell of internal diameter D with t is subjected to internal pressure p. The change in diameter is
A material having modulus of elasticity 200 GN/m2 and Poissons ratio 0.25 will have modulus of rigidity
A simply supported beam AB is loaded as shown in the figure below.
What is the shear force (SF) in kN in the portion AC of the beam?
A shaft is initially subjected to bending moment and then to torsion. In that case, if the magnitude of bending moment is found to be the same as that of torque, then the ratio of maximum bending stress to shear stress would be
A steel rod, 100 mm long, is held between two rigid supports. It is heated to 20°C. If the coefficient of thermal expansion of the material of the rod is 15 x 10-6/°C and the modulus of elasticity is 200 x 103 MN/m2, what is the stress in the rod?
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long. It is subjected to a longitudinal tensile stress of 440 N/mm2 and a lateral compressive stress of 200 N/mm2 in perpendicular directions. E = 2 x 10-5 N/ mm2, μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?
At a certain point in a structural member, there are perpendicular stresses 80 N/mm2 and 20 N/mm2, both tensile. What is the equivalent stress in simple tension, according to the maximum principal strain theory? (Poisson’s ratio = 0.25)
The free end of a cantilever beam is supported by the free end of another cantilever beam using a roller as shown in the figure given below. What is the deflection at the roller support B?
Mohar's Circle given below corresponds to which one of the following stress conditions?
A 2-m long rod at a temperature of 10°C is allowed to expand with temperature rising to 80°C. (E = 100,000 MN/m2 and X= 0.000012°C)
Q. The expension of the rod due to the rise in temperature will be
A 2-m long rod at a temperature of 10°C is allowed to expand with temperature rising to 80°C. (E = 100,000 MN/m2 and X= 0.000012°C)
Q. The stress in the rod, if expansion is not allowed, will be
Match list I with list II and select the correct answer using the codes given below:
Codes: ABCD
Match list I with list II and select the correct answer using the codes given below:
List I
Codes: ABCD
Top Courses for Mechanical Engineering
Important Questions for Fluid Mechanics, Strength Of Materials - 2
Fluid Mechanics, Strength Of Materials - 2 MCQs with Answers
Online Tests for Fluid Mechanics, Strength Of Materials - 2
|
© EduRev
|
Education Revolution
|
Follow Us
|
