GATE  >  Production & Engineering Materials - 2

# Production & Engineering Materials - 2

Test Description

## 20 Questions MCQ Test GATE Mechanical (ME) 2023 Mock Test Series | Production & Engineering Materials - 2

Production & Engineering Materials - 2 for GATE 2022 is part of GATE Mechanical (ME) 2023 Mock Test Series preparation. The Production & Engineering Materials - 2 questions and answers have been prepared according to the GATE exam syllabus.The Production & Engineering Materials - 2 MCQs are made for GATE 2022 Exam. Find important definitions, questions, notes, meanings, examples, exercises, MCQs and online tests for Production & Engineering Materials - 2 below.
Solutions of Production & Engineering Materials - 2 questions in English are available as part of our GATE Mechanical (ME) 2023 Mock Test Series for GATE & Production & Engineering Materials - 2 solutions in Hindi for GATE Mechanical (ME) 2023 Mock Test Series course. Download more important topics, notes, lectures and mock test series for GATE Exam by signing up for free. Attempt Production & Engineering Materials - 2 | 20 questions in 60 minutes | Mock test for GATE preparation | Free important questions MCQ to study GATE Mechanical (ME) 2023 Mock Test Series for GATE Exam | Download free PDF with solutions
 1 Crore+ students have signed up on EduRev. Have you?
Production & Engineering Materials - 2 - Question 1

### Draft on pattern for casting is

Production & Engineering Materials - 2 - Question 2

### Slag inclusion in casting is a

Production & Engineering Materials - 2 - Question 3

### True centrifugal casting

Production & Engineering Materials - 2 - Question 4

Blind risers

Production & Engineering Materials - 2 - Question 5

In the measurement of surface roughness, heights of successive 10 peaks and troughs were measured from a datum and were 33, 25, 30, 19, 22, 18, 32, 27, 29, and 20 microns. If these measurements were made over a 5 mm length. The CLA value for the given surface is

Detailed Solution for Production & Engineering Materials - 2 - Question 5

*Answer can only contain numeric values
Production & Engineering Materials - 2 - Question 6

A casting of cube of side 30 cm requires cylindrical side riser. The minimum height of side riser can be chosen is __________ (in mm)

Detailed Solution for Production & Engineering Materials - 2 - Question 6

Side Riser : For optimum side riser exposed surface area (A) should be minimum,

at least riser should solidify along with casting. So

Production & Engineering Materials - 2 - Question 7

The thickness of metallic sheet is reduced from an initial thickness of 16 mm to a final required thickness in one single pass rolling with a pair of cylindrical rollers each of diameter of 400 mm and angle of bits 9.8°. The final required thickness is

Detailed Solution for Production & Engineering Materials - 2 - Question 7

Given,
Initial thickness (h1) = 16 mm
Final thickness (h2)
Roll diameter = 400 mm
We know that

*Answer can only contain numeric values
Production & Engineering Materials - 2 - Question 8

For the given casting of size 40x40x20cm having cylindrical riser of radius 15 cm and height 20cm the time (in sec) required to fill the entire casting and riser is _____

Detailed Solution for Production & Engineering Materials - 2 - Question 8

Production & Engineering Materials - 2 - Question 9

The results of machining steel with two grades of tool are given below

For a 180 min tool life which tool is required

Detailed Solution for Production & Engineering Materials - 2 - Question 9

Tool A : as VA > VB ⇒ higher speed leads to higher productivity

*Answer can only contain numeric values
Production & Engineering Materials - 2 - Question 10

An Aluminium rod is drawn into wire of required diameter. Semi die angle is 10°. The friction to be 0.04 and nominal stress 35 MPa. The maximum reduction that can be given to material i s ______________ % .

Detailed Solution for Production & Engineering Materials - 2 - Question 10

Production & Engineering Materials - 2 - Question 11

A resistance strain gauge experiences 1% change in resistance when subjected to a uniaxial strain of 5000 μm/m. if gauge lactor is assumed as 1.9 then measured value will be

Detailed Solution for Production & Engineering Materials - 2 - Question 11

*Answer can only contain numeric values
Production & Engineering Materials - 2 - Question 12

A tube 30mm outer diameter is turned on lathe the cutting velocity of tool is 10 m/min. If rake angle is 35°, depth of cut is 0.15mm, length of chip is 60 mm. The velocity of chip relative to workpiece is _______________(m/min)

Detailed Solution for Production & Engineering Materials - 2 - Question 12

Production & Engineering Materials - 2 - Question 13

A 63.5 mm dia plain milling cutter having 6 tooth is used to face mill a block of aluminum 18cm long and 3 cm wide. The spindle speed is I500 rpm and teed is 0.0125mm/rev, the time taken per cut is

Detailed Solution for Production & Engineering Materials - 2 - Question 13

*Answer can only contain numeric values
Production & Engineering Materials - 2 - Question 14

A stepper motor drive having step angle 7.2°/step is used for driving an axis in the NC machine. The motor is connected to the lead screw through a gear having gear ratio (output speed / input speed) is 1/3 and lead screw with pitch of 3 mm & no. of starts is 2. The positional accuracy of the axis of the machine i s _______ μ m.

Detailed Solution for Production & Engineering Materials - 2 - Question 14

Production & Engineering Materials - 2 - Question 15

A shaft of dimension 40 ± 0.1mm is produced with a circularity error of 0.05mm on maximum material limit. To produce clearance fit between the hole and shaft, the minimum size of the hole required is

Detailed Solution for Production & Engineering Materials - 2 - Question 15

Mm size of Hole = L-limit of hole
= Maximum Material Limit (MML) of hole
= MML of shaft +circularity error
= 40.1 +0.05 =40.15 mm

*Answer can only contain numeric values
Production & Engineering Materials - 2 - Question 16

During electric discharge machining operation for drilling a square hole of 10 mm in low carbon steel plate of 5 mm thick, brass tool and kerosene are used. The resistance and capacitance of relaxation circuit are 50 Ω and 10 μF, respectively. The gap is maintained at such a value that the discharge takes place at 150 Volts. If the cycle time of the power supply is 0.7 milliseconds, the average power input in kW for the EDM process will be _____

Detailed Solution for Production & Engineering Materials - 2 - Question 16

W = 0.1607 kW

Production & Engineering Materials - 2 - Question 17

A shaft of dimension is to be inspected by using GO and NOGO gauges. The lower and upper limits of GO gauge respectively when the gauge tolerance and wear allowance each is taken as 10% of work tolerance are

Detailed Solution for Production & Engineering Materials - 2 - Question 17

Production & Engineering Materials - 2 - Question 18

The following statements are corresponding to metal forming process

1. Deforming Tungsten at 1000°C is considered as cold working process
2. If the type of load applied is tensile load, it is necessary to maintain load for some more time
3. If the type of load applied is compression load, it is necessary to maintain load for some more time
4. In all the metals increase in temperature causes decrease in yield strength of metal.
5. In case of lead and tin, the cold working is done at temperature below 0°C

Which of the above statement are correct

Detailed Solution for Production & Engineering Materials - 2 - Question 18

In case compressive type load application it is not necessary to maintain tlie load applied because when the stress induced is greater than the flow stress no elastic deformation is present in the material. In all the metals increase in temperature causes reduction in yield stress except steel.

Production & Engineering Materials - 2 - Question 19

An L-shaped component is produced by bending with total leg length of horizontal leg is 80mm and vertical leg is 60mm and inside radius of the corner is 8mm and thickness of the sheet is 2mm. The developed length of the strip is

Detailed Solution for Production & Engineering Materials - 2 - Question 19

Production & Engineering Materials - 2 - Question 20

A 24 teeth gear is to be produced using simple indexing mechanism, the following plates can be used

Plate 1: 15, 16, 17, 18, 19 and 20
Plate 2: 21, 23, 27, 29, 31 and 33
Plate 3: 35, 37, 39,41,43,47 and 49

Detailed Solution for Production & Engineering Materials - 2 - Question 20

N = 24

Hence all the 3 - plates can be used.

## GATE Mechanical (ME) 2023 Mock Test Series

25 docs|229 tests
 Use Code STAYHOME200 and get INR 200 additional OFF Use Coupon Code
Information about Production & Engineering Materials - 2 Page
In this test you can find the Exam questions for Production & Engineering Materials - 2 solved & explained in the simplest way possible. Besides giving Questions and answers for Production & Engineering Materials - 2, EduRev gives you an ample number of Online tests for practice

## GATE Mechanical (ME) 2023 Mock Test Series

25 docs|229 tests