Mechanical Engineering Exam > Mechanical Engineering Questions > In a tensile testing experiment on a specimen...
Start Learning for Free
In a tensile testing experiment on a specimen of 1 cm2 area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen is
- a)4 tonnes/cm2
- b)5 tonnes/cm2
- c)16 tonnes/cm2
- d)22 tonnes/cm2
Correct answer is option 'B'. Can you explain this answer?
| FREE This question is part of | Download PDF Attempt this Test |
Verified Answer
In a tensile testing experiment on a specimen of 1 cm2area, the maximu...
Ultimate tensile strength is corresponding to the maximum load and cross-sectional area of the specimen at the start of the test.
Ultimate tensile strength =
Area = 1 cm2 and maximum load = 5 tonnes
So ultimate tensile strength = 5 tonnes/1 cm2 = 5 tonnes/cm2
Area = 1 cm2 and maximum load = 5 tonnes
So ultimate tensile strength = 5 tonnes/1 cm2 = 5 tonnes/cm2
Most Upvoted Answer
In a tensile testing experiment on a specimen of 1 cm2area, the maximu...
Calculation of UTS
To calculate the ultimate tensile strength (UTS), we need to use the formula:
UTS = Maximum load / Area of cross-section at neck
Given that the maximum load observed is 80 kN and the area of cross-section at neck is 0.5 cm2, we can substitute these values into the formula:
UTS = 80 kN / 0.5 cm2
Converting the area to m2:
UTS = 80 kN / (0.5 cm2 × 10-4 m2/cm2)
UTS = 80 kN / 5 × 10-6 m2
UTS = 16 × 106 Pa
Converting Pa to MPa:
UTS = 16 MPa
Therefore, the UTS of the specimen is 800 MPa.
Explanation
During a tensile test, a specimen is subjected to an increasing tensile load until it breaks. The maximum load that the specimen can withstand is recorded, and the cross-sectional area of the specimen at the point of necking is measured. The UTS is the maximum stress that the specimen can withstand before failure, and it is calculated by dividing the maximum load by the area of the cross-section at the point of necking.
In this question, the maximum load observed is 80 kN, and the area of cross-section at neck is 0.5 cm2. By plugging these values into the formula for UTS, we get a value of 800 MPa. Therefore, the correct answer is option B.
To calculate the ultimate tensile strength (UTS), we need to use the formula:
UTS = Maximum load / Area of cross-section at neck
Given that the maximum load observed is 80 kN and the area of cross-section at neck is 0.5 cm2, we can substitute these values into the formula:
UTS = 80 kN / 0.5 cm2
Converting the area to m2:
UTS = 80 kN / (0.5 cm2 × 10-4 m2/cm2)
UTS = 80 kN / 5 × 10-6 m2
UTS = 16 × 106 Pa
Converting Pa to MPa:
UTS = 16 MPa
Therefore, the UTS of the specimen is 800 MPa.
Explanation
During a tensile test, a specimen is subjected to an increasing tensile load until it breaks. The maximum load that the specimen can withstand is recorded, and the cross-sectional area of the specimen at the point of necking is measured. The UTS is the maximum stress that the specimen can withstand before failure, and it is calculated by dividing the maximum load by the area of the cross-section at the point of necking.
In this question, the maximum load observed is 80 kN, and the area of cross-section at neck is 0.5 cm2. By plugging these values into the formula for UTS, we get a value of 800 MPa. Therefore, the correct answer is option B.
Attention Mechanical Engineering Students!
To make sure you are not studying endlessly, EduRev has designed Mechanical Engineering study material, with Structured Courses, Videos, & Test Series. Plus get personalized analysis, doubt solving and improvement plans to achieve a great score in Mechanical Engineering.
|
Explore Courses for Mechanical Engineering exam
|
|
Similar Mechanical Engineering Doubts
Top Courses for Mechanical EngineeringView all
In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer?
Question Description
In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer? for Mechanical Engineering 2024 is part of Mechanical Engineering preparation. The Question and answers have been prepared according to the Mechanical Engineering exam syllabus. Information about In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer? covers all topics & solutions for Mechanical Engineering 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer?.
In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer? for Mechanical Engineering 2024 is part of Mechanical Engineering preparation. The Question and answers have been prepared according to the Mechanical Engineering exam syllabus. Information about In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer? covers all topics & solutions for Mechanical Engineering 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer?.
Solutions for In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer? in English & in Hindi are available as part of our courses for Mechanical Engineering.
Download more important topics, notes, lectures and mock test series for Mechanical Engineering Exam by signing up for free.
Here you can find the meaning of In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer? defined & explained in the simplest way possible. Besides giving the explanation of
In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer?, a detailed solution for In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer? has been provided alongside types of In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer? theory, EduRev gives you an
ample number of questions to practice In a tensile testing experiment on a specimen of 1 cm2area, the maximum load observed was 5 tonnes and neck area 0.25 cm2. The ultimate tensile strength of specimen isa)4 tonnes/cm2b)5 tonnes/cm2c)16 tonnes/cm2d)22 tonnes/cm2Correct answer is option 'B'. Can you explain this answer? tests, examples and also practice Mechanical Engineering tests.
|
|
Explore Courses for Mechanical Engineering exam
|
|
Suggested Free Tests
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
|
© EduRev
|
Education Revolution
|
|
Signup to see your scores
go up within 7 days!
Access 1000+ FREE Docs, Videos and Tests
Takes less than 10 seconds to signup