Electrical Engineering (EE) Exam  >  Electrical Engineering (EE) Notes  >  Power Electronics  >  Power Semiconductor Devices - 2

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE) PDF Download

TRANSISTOR AS A SWITCH

The transistor is used as a switch therefore it is used only between saturation and cutoff. From fig. 5 we can write the following equations

 Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

Fig. 6: Transistor Switch

If the base current is increased above I BM ,VBE increases, the collector current increases and VCE falls below VBE . This continues until the CBJ is forward biased with VBC
of about 0.4 to 0.5V, the transistor than goes into saturation. The transistor saturation may be defined as the point above which any increase in the base current does not increase the collector current significantly.
In saturation, the collector current remains almost constant. If the collector emitter voltage is VCE sat the collector current is
VBE increases due to increased base current resulting in increased power loss. Once the
transistor is saturated, the CE voltage is not reduced in relation to increase in base current. However the power is increased at a high value of ODF, the transistor may be damaged Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)it may operate in active region, VCE increases resulting in increased power loss.


SWITCHING CHARACTERISTICS

A forward biased p-n junction exhibits two parallel capacitances; a depletion layer capacitance and a diffusion capacitance. On the other hand, a reverse biased p-n junction has only depletion capacitance. Under steady state the capacitances do not play any role. However under transient conditions, they influence turn-on and turn-off behavior of the transistor.

TRANSIENT MODEL OF BJT

 Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

Due to internal capacitances, the transistor does not turn on instantly. As the voltage VB rises from zero to V1 and the base current rises to IB1, the collector current does not respond immediately. There is a delay known as delay time td, before any collector current flows. The delay is due to the time required to charge up the BEJ to the forward bias voltage VBE(0.7V). The collector current rises to the steady value of ICS and this time is called rise time tr.
The base current is normally more than that required to saturate the transistor. As a result excess minority carrier charge is stored in the base region. The higher the ODF, the greater is the amount of extra charge stored in the base. This extra charge which is called the saturating charge is proportional to the excess base drive.
This extra charge which is called the saturating charge, is proportional to the excess base drive and the corresponding current Ie.
When the input voltage is reversed from V1 to -V2, the reverse current –IB2 helps to discharge the base. Without –IB2 the saturating charge has to be removed entirely due to recombination and the storage time ts would be longer.
Once the extra charge is removed, BEJ charges to the input voltage –V2 and the base current falls to zero. tf depends on the time constant which is determined by the reverse biased BEJ capacitance.

Turn-on time tonThe turn-on time can be decreased by increasing the base drive for a fixed value of collector current. td is dependent on input capacitance does not change significantly with IC . However tr increases with increase in IC .

Turn off time toffThe storage time tis dependent on over drive factor and does not change significantly with IC. tf is a function of capacitance and increases with IC.
ts & tf can be reduced by providing negative base drive during turn-off. tf is less sensitive to negative base drive.

Cross-over tC : The crossover time tC is defined as the interval during which the collector voltage VCE rises from 10% of its peak off state value and collector current. IC falls to 10% of its on-state value. tC is a function of collector current negative base drive.


1.13 POWER DERATING

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

BREAK DOWN VOLTAGES

A break down voltage is defined as the absolute maximum voltage between two terminals with the third terminal open, shorted or biased in either forward or reverse direction.
BVSUS : The maximum voltage between the collector and emitter that can be sustained across the transistor when it is carrying substantial collector current.
BVCEO : The maximum voltage between the collector and emitter terminal with base open circuited.
BVCBO : This is the collector to base break down voltage when emitter is open circuited.

BASE DRIVE CONTROL

This is required to optimize the base drive of transistor. Optimization is required to increase switching speeds. ton can be reduced by allowing base current peaking during
can be increased to a sufficiently high value to maintain the transistor in quasi-saturation region. toff can be reduced by reversing base current and allowing base current peaking during turn off since increasing IB 2 decreases storage time.

A typical waveform for base current is shown.

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)


Some common types of optimizing base drive of transistor are

  • Turn-on Control.
  • Turn-off Control.
  • Proportional Base Control.
  • Antisaturation Control


TURN-ON CONTROL

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

When input voltage is turned on, the base current is limited by resistor R1 and C1 discharges through R2. The discharging time constant is 2 R2 C1 . To allow sufficient charging and discharging time, the width of base pulse must be t1 1 and off


TURN-OFF CONTROL

If the input voltage is changed to during turn-off the capacitor voltage Vis added to V2 as reverse voltage across the transistor. There will be base current peaking during turn off. As the capacitor Cdischarges, the reverse voltage will be reduced to a steady state value, V2 . If different turn-on and turn-off characteristics are required, a turn-off  Circuit Using C 2 , R3 & R maybe added. The diode Disolates the forward base drive circuit from the reverse base drive circuit during turn off.

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

PROPORTIONAL BASE CONTROL

This type of control has advantages over the constant drive circuit. If the collector current changes due to change in load demand, the base drive current is changed in proportion to collector current.
When switch S1 is turned on a pulse current of short duration would flow through the base of transistor Qand Qis turned on into saturation. Once the collector current starts to flow, a corresponding base current is induced due to transformer action. The transistor would latch on itself and S1 can be turned off. For proper operation of the circuit, the magnetizing current which must be much smaller than the collector current should be as small as possible. The switch S1 can be implemented by a small signal transistor and additional arrangement is necessary to discharge capacitor C1 and reset the transformer core during turn-off of the power transistor.


ANTISATURATION CONTROL

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

If a transistor is driven hard, the storage time which is proportional to the base current increases and the switching speed is reduced. The storage time can be reduced by operating the transistor in soft saturation rather than hard saturation. This can be accomplished by clamping CE voltage to a pre-determined level and the collector current
is given by IC      Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

Where VCM is the clamping voltage and VCM VCE sat .
This means that the CE voltage is raised above saturation level and there are no excess carriers in the base and storage time is reduced.
The clamping action thus results a reduced collector current and almost elimination of the storage time. At the same time, a fast turn-on is accomplished.
However, due to increased VCE , the on-state power dissipation in the transistor is increased, whereas the switching power loss is decreased.


ADVANTAGES OF BJT’S

  • BJT’s have high switching frequencies since their turn-on and turn-off time are low.
  • The turn-on losses of a BJT are small.
  • BJT has controlled turn-on and turn-off characteristics since base drive control is possible.
  • BJT does not require commutation circuits.


DEMERITS OF BJT Drive circuit of BJT is complex.

  • It has the problem of charge storage which sets a limit on switching frequencies.
  • It cannot be used in parallel operation due to problems of negative temperature coefficient.


POWER MOSFETS

INTRODUCTION TO FET’S

FET’s use field effect for their operation. FET is manufactured by diffusing two areas of p-type into the n-type semiconductor as shown. Each p-region is connected to a gate terminal; the gate is a p-region while source and drain are n-region. Since it is similar to two diodes one is a gate source diode and the other is a gate drain diode.

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)


In BJT’s we forward bias the B-E diode but in a JFET, we always reverse bias the gate-source diode. Since only a small reverse current can exist in the gate lead. Therefore IG 0 , therefore Rin ideal
The term field effect is related to the depletion layers around each p-region as shown. When the supply voltage VDD is applied as shown it forces free electrons to flow
from source to drain. With gate reverse biased, the electrons need to flow from source to drain, they must pass through the narrow channel between the two depletion layers. The more the negative gate voltage is the tighter the channel becomes.
Therefore JFET acts as a voltage controlled device rather than a current controlled
device.
JFET has almost infinite input impedance but the price paid for this is loss of control over the output current, since JFET is less sensitive to changes in the output voltage than a BJT.

JFET CHARACTERISTICS

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

The maximum drain current out of a JFET occurs when VGS   0   As VDS is increased for 0 to a few volts, the current will increase as determined by ohms law. As VDS approaches VP the depletion region will widen, carrying a noticeable reduction in channel width. If VDS is increased to a level where the two depletion region would touch a pinch-off will result. ID now maintains a saturation level IDSS . Between 0 volts and pinch off voltage VP is the ohmic region. After VP , the regions constant current or active
region.
If negative voltage is applied between gate and source the depletion region similar to those obtained with VGS  0 are formad but at lower values of VDS . Therefore saturation level is reached earlier.


Classification of MOSFET

MOSFET stands for metal oxide semiconductor field effect transistor. There are two types of MOSFET

  • Depletion type MOSFET
  • Enhancement type MOSFET


DEPLETION TYPE MOSFET

CONSTRUCTION

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

Symbol of n-channel depletion type MOSFET

It consists of a highly doped p-type substrate into which two blocks of heavily doped n-type material are diffused to form a source and drain. A n-channel is formed by diffusing between source and drain. A thin layer of SiOis grown over the entire surface
and holes are cut in SiO2 to make contact with n-type blocks. The gate is also connected to a metal contact surface but remains insulated from the n-channel by the SiO2 layer. SiO2 layer results in an extremely high input impedance of the order of 1010 to 1015  for this years 

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

fig. 4: Structure of n-channel depletion type MOSFET


OPERATION

When VGS 0V and VDS is applied and current flows from drain to source similar to JFET. When VGS    1V , the negative potential will tend to pressure electrons towards
the p-type substrate and attracts hole from p-type substrate. Therefore recombination occurs and will reduce the number of free electrons in the n-channel for conduction. Therefore with increased negative gate voltage ID reduces.
For positive values,Vgs , additional electrons from p-substrate will flow into the
channel and establish new carriers which will result in an increase in drain current with positive gate voltage.


DRAIN CHARACTERISTICS

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

 TRANSFER CHARACTERISTICS
Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

The document Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE) is a part of the Electrical Engineering (EE) Course Power Electronics.
All you need of Electrical Engineering (EE) at this link: Electrical Engineering (EE)
5 videos|50 docs|46 tests

Top Courses for Electrical Engineering (EE)

FAQs on Power Semiconductor Devices - 2 - Power Electronics - Electrical Engineering (EE)

1. What are power semiconductor devices?
Ans. Power semiconductor devices are electronic components that are specifically designed to handle high levels of electrical power. They are used in various applications such as power supplies, motor drives, inverters, and electric vehicles to control and switch high voltage and current levels efficiently.
2. What are the advantages of using power semiconductor devices?
Ans. Power semiconductor devices offer several advantages, including high efficiency, fast switching speeds, compact size, and improved reliability. They allow for better control and regulation of power, reducing energy losses and improving overall system performance.
3. What are the different types of power semiconductor devices?
Ans. There are several types of power semiconductor devices, including diodes, thyristors (such as SCR and TRIAC), power transistors (such as MOSFET and IGBT), and voltage regulators. Each type has its own unique characteristics and is suitable for specific applications.
4. How do power semiconductor devices work?
Ans. Power semiconductor devices work by controlling the flow of electrical current through a semiconductor material. They use various principles such as rectification, amplification, and switching to regulate the power flow and perform the desired functions. For example, a power transistor can amplify or switch electrical signals, while a diode allows current to flow in only one direction.
5. What are some common applications of power semiconductor devices?
Ans. Power semiconductor devices find applications in a wide range of industries, including automotive, telecommunications, industrial automation, renewable energy, and consumer electronics. They are used in devices such as motor drives, power converters, uninterruptible power supplies (UPS), solar inverters, and electric vehicle charging systems, among others.
5 videos|50 docs|46 tests
Download as PDF
Explore Courses for Electrical Engineering (EE) exam

Top Courses for Electrical Engineering (EE)

Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
10M+ students study on EduRev
Related Searches

mock tests for examination

,

Summary

,

video lectures

,

Free

,

Important questions

,

shortcuts and tricks

,

past year papers

,

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

,

Viva Questions

,

Previous Year Questions with Solutions

,

ppt

,

Exam

,

Sample Paper

,

Extra Questions

,

pdf

,

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

,

Objective type Questions

,

MCQs

,

study material

,

practice quizzes

,

Power Semiconductor Devices - 2 | Power Electronics - Electrical Engineering (EE)

,

Semester Notes

;