Development of Moment Distribution Method - Displacement Method, Strength of Materials | Strength of Material Notes - Agricultural Engg - Agricultural Engineering PDF Download

Development of Moment Distribution Method

In this lesson, the generic procedure of the Moment Distribution Method is illustrated through an example.  Consider a two span continuous beam ABC as shwon in Figure 16.1.

Fig.16.1.

The steps involved in moment distribution method are described bellow and also depicted in Figure 16.1.

Step 1: Fixed end Moments

First assume each span of the continuous beam as fixed beam and calculate the corresponding fixed end moments.

\[M{}_{FAB}=-{{3 \times {5^2}} \over {12}}=-6.25{\rm{ kNm}}\] ;    \[M{}_{FBA} = {{3 \times {5^2}} \over {12}} = 6.25{\rm{ kNm}}\]

\[M{}_{FBC}=-{{10 \times 2 \times {3^2}} \over {{5^2}}}=-7.2{\rm{ kNm}}\]  ;  \[M{}_{FCB}=-{{10 \times 3 \times {2^2}} \over {{5^2}}}=4.8{\rm{ kNm}}\]

Assume \[M{}_{AB}=M{}_{FAB}=-6.25{\rm{ kNm}}\] ,  \[M{}_{BA}=M{}_{FBA}=6.25{\rm{ kNm}}\] , \[M{}_{BC}=M{}_{FBC}=-7.2{\rm{ kNm}}\]  AND \[M{}_{CB}=M{}_{FCB}=4.8{\rm{ kNm}}\]

Step 2: Unbalnced moment

Equilibriuam condition at B is \[M{}_{BA} + M{}_{BC} = 0\]  . However initial assumption of  \[M{}_{BA}\]  and  \[M{}_{BC}\] gives,

\[M{}_{BA} + M{}_{BC} = 6.25 - 7.2 =-0.95\]

Therefore at joint B there is an unbalanced moment of - 0.95 kNm.

Since ends A and C are fixed, there is no unbalanced moment at A and C.

Step 3: Balancing moment

Apply a balancing moment of 0.95 kNm at B.

Step 4: Distribution of balancing moment

Applied balancing momnet at B is then distributed among the connecting member i.e., BA and BC in porportion to their stiffness. The distribued moments are determined by multiplying the unbalanced moment by the distribution factor of the respective member.

From lesson 15.1.3 we have,.

\[{k_{BA}} = {{4E{I_{BA}}} \over {{L_{BA}}}} = {{4EI} \over 5}\]  and  \[{k_{BC}} = {{4E{I_{BC}}} \over {{L_{BC}}}} = {{4EI} \over 5}\]

Distribution factors for BA and BC are,

Therefore, distributed moment for BA and BC will be  \[0.5 \times 0.95 = 0.475{\rm{ kNm}}\] .

Step 5: Carry over of distributed moment

For member AB, distributed moment at B will cause carried over moment at A. Simiarlary for member BC, distributed moment at B will cause carried over moment at C. These carried over moments are determined by multiplying the distributed moment by the carried over factor of the respective member.

\[{C_{BA}} = {1 \over 2}\]   and   \[{C_{BC}} = {1 \over 2}\]

Therefore carried over moments are,

At A \[0.5 \times 0.475 = 0.2375{\rm{ kNm}}\]

At C \[0.5 \times 0.475 = 0.2375{\rm{ kNm}}\]

Step 6: Total moment at the end of cycle

Determine the total moment each end.

Total moment = Fixed end moment (Step 1) + Distributed unbalanced moment (Step 4) + Carried over moment (Step 5)

\[M{}_{AB}=-6.25 + 0.2375=-6.0125{\rm{ kNm}}\]

\[M{}_{BA}=6.250 + 0.475=6.725{\rm{ kNm}}\]

\[M{}_{BC}=-7.20 + 0.475=-6.725{\rm{ kNm}}\]

\[M{}_{AB}=4.8 + 0.2375=5.0375{\rm{ kNm}}\]

Step 2 to Step 6 is a complete cycle. At the end of each cycle check whether equilibrium equations are satisfed.

\[M{}_{BA} + M{}_{BC} = 6.725 - 6.725 = 0\]  => Equilibrium equation at B is satisfied.

If it is found that there are joints with unbalanced moment then again go to step 2 and repeat the cycle until all the unbalanced moments become zero.

Generally the entire calculation in moment distribution method is done in a tabular form as illustrated bellow.