AutoCAD Walkthrough Tutorial Video Lecture | A complete Guide to AutoCAD (English) - Design Softwares

in this tutorial we will learn how to
create walkthrough so for creation of
walkthrough you have to give any path
and is the shortcut any path combat now
here you you will have to define the
camera and target so you can define
camera as a point or path and target is
also defined as the point or path so
suppose I want to define the camera as a
point and target as a putt so for that I
will have to create a path actually for
target so suppose I want to give target
lies so for that I will create one line
take the line come back and I will take
this make our all from this end point to
this end point in this way I want to
show the skip
and then my camera I will fix suppose
at some position so I will for that also
I will draw one line take this line from
this point to this point
enter again press ENTER to repeat the
line command from it I will take it off
worth so here I want to keep the camera
position so again give any path command
any enter ten for camera I will use a
point so click on this and define camera
here point name is oh okay then target
will be a path so click here and give
this line as a target okay then adjust
the duration suppose I want to animation
for five seconds preview click on three
so in this way it will
show you the walkthrough by keeping
camera fix and giving a path so in this
way you can also do the reverse also so
for camera you can give a path and for
target you can give a point so to do
that that we will see so for that for
camera actually we want to give a path
so suppose we will create a one circle
sir circle around this so for that click
on this top and take the circle command
and take some point here click and click
outside then orbit it and see the circle
is created so I want this to be up so I
will move it select object
winter so suppose I will take make orth
on a pet and give some height so was I
giving giving it to meter as the height
then I will again give any path command
any pot then for camera I will choose
this path click on this select this
circle okay for target I am choosing a
point
so again click on this button and give
some point in between suppose I want to
give point somewhere between here okay
give the duration suppose five second
again click on preview so it is going
very fast so if you want to make it slow
you will have to increase the time so it
will run slower so here camera position
actually target point I have to make it
up so camera opposition is I will move
this camera down actually to show it
properly move give the base point give
the second point then again I will go
for any path then for camera path click
for target point click suppose I will
give some point here
okay then the reason 15-second preview
so it is showing that I am looking from
down
RM
so you can give suppose path camera as a
path and target as a point so same way
you can give both as a path also so for
that suppose so forgiving that path we
will create one more circle click the
top so we will create a bigger circle
than this or we will increase the click
on this grip and increase the radius and
we'll keep one smaller circle as a
target again circle give the center
point then make this smaller circle
now I will move this circle up more
select object enter give the base point
in the empty space give the direction
and click again give any path then for
camera path click this will be the
camera okay
for target also path click take this as
a target okay do duration 20 second view
so in this way it is camera is also
rotating and your target is also
rotating so in this way you can show the
building from all the sides very easily
so in this view you can you target for
both camera and target and from here you
can see the different in different
visual style or the effect is that you
can see by changing it so it is with
material actually the metal we have
played in the previous tutorial same
this way you can see the effect the
front a bit sketchy wireframe then x-ray
the transparent conception or shaded in
this way you can see the effect and if
you want to reverse it by clicking on
this we can make it flow reverse we can
make it rotate reverse seen that way
also you can do it then once all setting
has been done you can choose the final
output in which output you want so you
can have also render image also if you
want if you applied material and all
those things you can see the render
image or all these different add final
presentation images also there so it
will take time as per your settings to
generate so I will take suppose shaded
and it will take more time for
generations I will take suppose only two
seconds so it will happen quickly then
from here you can choose the type of
file you want the extension of the file
so normally I choose avi file and from
here you can control the resolution and
then click on OK so it will then give
the name
suppose I will say animation follow-up
to and save so it will create a file for
that here you can see so it has created
actually so you can check that by
clicking your browser so it is
walkthrough by doubling on it you can
give it so in this way
you can create output file swiftly so if
you I want to shows it from inside now
all these we are created from outside if
I want to create it from inside so to do
that that we will see so we just erase
all these lines don't need these lines
just here is it you touch then for
showing from inside
take your top view
I don't want this camera also I will
delete it
take a click on this top and make it
wire film so ok so same way I will have
to draw two paths one for camera and one
for target so that path should be
connected so we will be using polyline
so that it will remain connected so
click on this polyline or before that
suppose I want to show only one room so
for that again you can use the circle
actually suppose I want to show this
room only so create one circle for it or
camera we will keep at the point so
select one circle for target suppose
this is my target so move it up so
and for camera I will create one
reference for point so I will create a
line give a ll enter from center of this
circle of previous point this kid so
from this point I will view towards this
circle so again you ne enter then for
camera point click on this button give
this point okay for target path is the
options click on this button give this
circle as a path okay then choose the
duration suppose 10 second preview so in
this way you can show the room from
inside and you can adjust the height of
the camera and the target to
make a different views so in this way
you can show single room from inside so
it will be useful for interior people's
interior designer people's so this is
showing one room and suppose I want to
show them all the rooms so for that
again we will go for top we will erase
this we enter select object enter so for
that I will have to create two paths one
for camera and other for target
so the path should be connected so I
will use polyline suppose I will start
from here from this room so at first I
am creating a target path so I will make
the objects nap box so that it will not
go anywhere so it will come at a
position I want and click the way you
want to you want your target or to move
all in a sequence you want to show the
rooms you draw the line target line
so from this room I will directly come
to this room okay
escape this
a target line then I will need a camera
line so again for that I will create a
polyline suppose song so these two lines
camera line and target line should not
cross each other so I will go in this
one
so take care that but don't cross each
other otherwise it will not create the
walkthrough
okay enter then I will move these lines
so take more command take this target
line enter base point do the height then
again enter take this camera line enter
give the other point so again give any
enter then for camera click on this
button take this inner path okay for
target take this external path okay give
some more time because it is a bigger
path and click on this for you so it
will go in inside each and every room
and it will show it so you will have to
do some hit and trials and edges the
things properly and to remove the
jerking it is actually jerking in
between so you can remove that by giving
your fill it to the camera path and
so forgiving that Filat click on this
fill it so that it will move smoothly so
give the fill it
then select then click on this radius
take one point give the other point
suppose I will take radius of 0.6 then
click on this polyline option and click
on one polyline so it will create the
arcs at different points same way for
our camera fill it select polyline
select on the this arc cindy way it will
give give a smoothness then again go
back to a symmetry zoom and again we
will try it
animation any any path then for camera
this is the camera in internal okay and
this is the target okay
then clear okay we will have to increase
the time actually so is forty second you
see it will go smoothly
outer edges the actually high-top target
and camera properly so it will show it
properly or best way you can go for
individual rooms so that it will and
then combine you have to combine it so
if you want to the final it okay it take
the settings and okay so that file will
be created so that is one we will stop
here thank you
you