AutoCAD 2015 Tutorial for Beginners Complete | Drawing; Layers; Hatch; Dimensions; Pdf Video Lecture | A complete Guide to AutoCAD (English) - Design Softwares

in this tutorial we will create one
drawing in AutoCAD 2015 so click on
start drawing so we want to create this
drawing so at first we will have to set
the space using limits command so for
that the overall dimension is actually 1
1 10 and 15 160 plus this 31 90 Plus
this 2200 in 10 so we will take around
250 as a maximum workspace required so
for that you will have to give at first
limits Command just just type it and
press Enter
then specify the lower left corner to 0
comma 0 enter then upper right corner to
250 comma 250 enter then to apply these
limits you have to use zoom wall command
for that you give Z enter a enter then
at first we will have to create this
reference line so suppose we want to
create these two reference line so the
best way to create reference line is by
using construction lines so construction
line will give you line of infinite
length so click on construction line
click the first point suppose then to
make it straight make the ortho on click
on the ortho mode give the direction I
want one vertical line and one
horizontal line then press ENTER to come
out so suppose I have created this
vertical line in this horizontal line so
from the this line now these two lines
at a distance of half of the 76 so we
will create that by offsetting the lines
so click on offset then I want half of
the 76 so you can directly give here 76
by 2 enter then select this line on this
side 38 again select this line on other
side
click there then again next will be this
line needs to be upset at 50 and then
one 110 so again select this line go up
give the distance of 50 enter I can
select this line go up give the distance
of one 110 then next is this line is at
34 so select this line and give this
source of 34 then press ENTER to stop
the object c'mon so we have created all
the reference lines on next we can
create suppose the circle we want to
create this circle so these are the
three holes of dire 26 so we want to
create a circle with diameter so for
that you can click on the arrow click on
center diameter then give the center
point and give the diameter of 26 then
we want these two circles at these two
points so we can copy them so click on
copy select object enter then base point
so we will give centre of this circle or
midpoint of this line as a base point
and second point make the earth off and
second point will be this midpoint and
this midpoint then press escape then
next suppose we want to create this
circle of daya radius 22 so for that I
can click on the arrow Center radius
give the center point and radius of 22
then next will be suppose we want to
create this internal shape so that
radius 28 and radius 18 so we will
create two circles circles so Center
Point give radius of 28 then press enter
to repeat the last command so you can
repeat the last command by
the inter then give the Centrepointe
give the radius of 18 then int then you
can zoom it by rotating scroll towards
monitor so now I want to create one
tangent line here so for that click on
the line command then press shift and
right click and select tangent from here
tangent select click on the circle again
shift right click select tangent click
on the circle press ENTER again press
ENTER again shift right Lake tangent
click shift rightly tangent then press
Enter to stop come back now I want to
trim this object so for that you can
give directly trim command TR enter in
thing trim command here to you at first
reference object so I want to trim
between these two lines so at first
select these two lines then press Enter
and click on the object that you want to
rim then press ENTER to come out then
next will be so this shape is ready the
next I want to create this circle of 62
radius and center is from this point so
again circle radius center point and
radius is 62 so this circle is created
then next will be upper portion so here
this circle is created then next is 24
and 32 circles two circles then pan it
by pressing down the scroll and dragging
the mouse then click on again circle
give the center point so the radius is
32 and 24 so 32 enter I can enter give
the center point release is 24 so these
two circles are created then I want to
create
is arc of fortified radius so that arc
you can create using fill it command so
click on fill it so for fill it now
current radius is radius is zero so at
first you will have to set the radius so
click on this radius and give the value
of 45 enter then select first object
then second object so this fill it
radius will be eight then next is this
line tangent line again line shift
rightly tangent click shift rightly
tangent click then enter to comma then
next will be to create this again so it
is actually it is not given it is 18
radius arc so again we will give fill it
then radius 18 then select first circle
second circle now one side is developed
so we can mirror all those object on
other side so click on mirror select
these objects then the circle also
required then enter then give the first
point of mirror line so mirror line
always lies at the center so click this
as a first point and this as a second
point then your source object no enter
press enter in this way this object is
created then next will be suppose this
infinite length of lines I don't want it
I want to remove those lines so the
quickest way is to create one rectangle
three and rectangle so how much
objective you required as per that you
create it around it then trim click on
trim then select this as a cutting edge
zoom - enter then give f4 a fence
then click around the object and enter
then press escape so in this way
unwanted lines ugly mode then you can
erase this circle it is select this
circle enter then again I don't want
these lines to be longer so again I can
remove them by using break command so
click on break select object first point
give the second point again enter this
is the first point in this is a second
point we can same way for this also
enter from here to here
enter give the first point from where
you want to break and go outside and Li
so all the again here press enter and
repeat the command give the two points
okay then one more circle remained here
so that is of 20 radius so give fill it
radius 20 enter select first object
second object then I will have to trim
it so for that give the trim command
select the reference object so for
removing this circle then this arc and
this arc for removing this circle then
this arc for removing this two circle
then press enter then click on the
object you don't work or you want to
remove then these two arcs okay enter
then he reads he enter select this end
then here again trim TR enter these are
the reference object enter click to the
mode option and
so in this way and one more line is
required at the bottom so take the line
command go here intersection to
intersection enter then next will be we
will have to apply layers for centerline
and for other object also we will have
to make the layer so click on layer
properties and click here new layer then
give it for center then choose color
that you want okay then line type is
continuous line wait for printing you
can define the line weight from here so
forth Center should be printed supposed
to point 25 okay then for 0 object I
want to give some color suppose I want
it to be in this color okay then new for
dimension I am going to put the
dimension also create one layer dim then
choose the color okay
then Center dimension then one more
color so Center outside edges dimension
and for hatching also so we will create
new layer for hatching lines okay then
for actually for center we will have to
make the line type Center so click on
this continuous load click and see so
Center is here okay select the center
and one more for suppose sheet 2 and
sheet that one
so for that I will give vertical and for
sheet suppose I want thickness to be so
this point for you okay then outside
line
I want Ignis to be point for you then
for dim I want it to be at point three
and hatch I need at point thirty okay so
all the thickness has been assigned so
close this then select all the center
lines and click here and click on center
then place the skip now Center is not
properly visible so you can increase the
gap by given LTS command in yes enter
suppose I make it for you I will do
again give LTS suppose I will make it
eight now those are properly visible now
next I want to apply dimensions for that
I will make that dim layer current
now suppose at first I will give all the
radius so for that click here and take
the radius option so for here this
radians now here the dimension is not
properly visible so for that give T
inter-dimensional modify fit and
increase this scale suppose I will make
it 15 okay
close so it is properly visible and I
will have to make some other settings
also I don't want 4 zeros and all other
settings so for that again duty enter
modify I don't want 4 zeros for that go
to primer units and make it single zero
then for text I want it to be a go over
the dimension line and
we're ISO standard then I want a line
internal line for the radius so take
here then okay
and close so export data setting your
dimension will be visible and I want it
somewhat more bigger so again the enter
modify it make it suppose 25 okay looks
work it is now properly visible then the
next dimension radius suppose for this
circle of 60 to enter this circle 28
enter this circle 18 then this circle 24
this is of 32 then I want to you this
gap between these terrain if your XY is
here you can shift it by giving UCS icon
command enter now you see the horizontal
dimension click on linear first point
second point location then I want these
gaps I can enter from this line to this
line this 50 I gain from this line to
this line until the center this to 34
then this radius to be a team the
diameter of this circle so for that
click on diameter select this circle go
outside then I want to write here three
holes so double click on die 26 place
then right here three holes
click outside so in this way I think all
the dimension has been 45 again radius
click here so all the dimension has been
21 again radius 20 so I think all the
dimension now has been given then next
will be to apply the hatch so from here
you can apply so click on hatch and go
inside and click there now because of
the centre lines the highs getting
separated so just select escape select
it and delete it and make the centerline
layer off so that centre line will be
invisible then apply the hatch and click
so complete object will get hatching
then from here increase the scale
suppose I want it to be for you I want
more gap suppose it
so more than that 1525 okay and I want
string lines on the opposite side so
from here you can change the angle so
here this inclined line is considered as
0 so opposite of that will be 90 degree
enter then close as creation now I want
to shift it on the highest layer so
select this edge click on the home and
from here take the hatch layer press
escape then I can make the centerline
layer on so it will be visible so in
this way this object is created now
suppose I want to put sheet around it
branch it so for that if it is already
ready
then from insert you can insert it
inside the browse
select the sheet open okay then zoom and
pan and place it supposed this drawing
will need required a a3 sized sheet
drawing shape click here and using takes
command we can put the details whatever
details out here so from here take the
text single line suppose some title is
here give the start point then make our
throne give the height suppose height
will be around say one rotation angle
zero then write the suppose it is a
support click outside enter then we can
move it to place it properly same way
you can add all the text details you can
add the notes whatever notes you want
using M text multi-line takes give the
first point give the second point and
write down the notes nodes and suppose
notice all dimensions
so whatever nodes are there that you can
write you can format it in a way you
want then click outside so in this way
you can add in arrange it properly
press escape so in in this way you can
add all the details and suppose if you
want to make PDF of this drying for
sending to someone then click on this
plot command here ok actually this sheet
needs to be on the sheet layer so select
the object and click on sheet then press
escape now sheet layer is Center so
click on layer properties and layer
make it continuous continuous okay
close it so in this way this drawing is
ready so you
can if you want to make the PDF or you
if you want to take the print click on
this lot then click suppose I want to
create a PDF so take the DWG to PDF then
she link the seed size suppose this is
my a three size so suppose I want it to
be is a three for 20 by 290 say 1 then
click on this display window then give
the first point second point then Center
the plot then I want it to be in black
and white so click here and make it
monochrome yes then keep this tick plot
with line weights see the preview so in
this way this drawing wheel will be
created properly and will be plotted
with thickness so what your thickness be
given at the time of making layers those
thickness are applied then right-click
and plot and give the name to the PDF
say so if we see that PDF so close
document so in this way and that PDF is
created with layers so you can make the
layers on if required so in this way
this drawing is properly create so this
one so we stop here thanks for giving
the