Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1andshy;and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer? - EduRev Electronics and Communication Engineering (ECE) Question

Explore Courses UPSC Exam UPSC Test Series Free Notes EduRev Infinity

Open App

Electronics and Communication Engineering (ECE) Exam > Electronics and Communication Engineering (ECE) Questions > Circuit shows an op-amp circuit used for gene...

Join the Discussion on the App

Circuit shows an op-amp circuit used for generating the square waveform.

If the output frequency required in 1 kHz. then the possible values of R₁and R₂ can be respectively

a)
2k, 1.7k
b)
4k, 2k
c)
2k, 4k
d)
1.7k, 2k

Correct answer is option 'A'. Can you explain this answer?

FREE This question is part of

Analog Electronics - 6

Attempt Test

Attempt this Test

Verified Answer

Circuit shows an op-amp circuit used for generating the square wavefor...

Frequency of oscillation

If R₁ = 2k

R₂ = 0.859 × 2

= 1.7 k

Option 1 is correct.

View all questions of this test

View all answers Start learning for free

< Previous Question Next Question >

Explore Courses for Electronics and Communication Engineering (ECE) exam

Similar Electronics and Communication Engineering (ECE) Doubts

The intermediate frequency of an AM superheterodyne receiver is 460kHz and the local oscillator frequency {fLO ) of the mixer is set at the higher of the two possible values, such that fLO > fc always. If the carries frequency {fC of the receiver signal is 700kHz, then the carrier frequency of the corresponding image signal will be kHz

View answer

A carrier signal AC cosωCt is frequency modulated using a message signal 3 cos 103πt. If the signal-to-noise ratio at input and output of the receiver are found to be 20 dB and 40 dB respectively, then what will be the sensitivity (in kHz/V) of frequency modulator? (Answer up to two decimal places) Correct answer is '1.36'. Can you explain this answer?

View answer

For the amplifier circuit shown, the op-amp can deliver a maximum current of 100 mA and is powered by ±15 V supply. If the input to the amplifier is a triangular waveform as shown. The peak value of the output waveform is ______. Correct answer is between '4.9,5.1'. Can you explain this answer?

View answer

Read the following paragraph and answer the questions.A digital counter is a set of flipflops whose states change in response to the pulses applied at Input. Counters can be asynchronous counters or synchronous counters. A counter is an example of a state machine; the number of states is called the modulus. Two basic types of state machines are the Moore and the Mealy. In Moore machine, the combinational logic is a gate array with outputs that determine the next state of the flip-flops in the memory. For Mealy machine, the present state affects just as in Moore machine but in addition, the inputs also affect the outputs.Q. A binary ripple counter is required to count upto 16, 38310. If the clock frequency is 8.192 MHz, the number of flip-flops required and frequency of the output of MSB respectively are

View answer

For the circuit shown in figure, if the clock frequency is 10KHz, the frequency of the waveform at the output Q is _____________KHz Correct answer is '5'. Can you explain this answer?

View answer

Top Courses for Electronics and Communication Engineering (ECE)View all

GATE ECE (Electronics) Mock Test Series 2025

Network Theory (Electric Circuits)

Crash Course: Electronic Communication Engineering (ECE)

Top Courses for Electronics and Communication Engineering (ECE)

View all

Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer?

Share with a Friend

Answer this doubt

Question Description
Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer? for Electronics and Communication Engineering (ECE) 2024 is part of Electronics and Communication Engineering (ECE) preparation. The Question and answers have been prepared according to the Electronics and Communication Engineering (ECE) exam syllabus. Information about Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer? covers all topics & solutions for Electronics and Communication Engineering (ECE) 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer?.

Solutions for Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer? in English & in Hindi are available as part of our courses for Electronics and Communication Engineering (ECE). Download more important topics, notes, lectures and mock test series for Electronics and Communication Engineering (ECE) Exam by signing up for free.

Here you can find the meaning of Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer? defined & explained in the simplest way possible. Besides giving the explanation of Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer?, a detailed solution for Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer? has been provided alongside types of Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer? theory, EduRev gives you an ample number of questions to practice Circuit shows an op-amp circuit used for generating the square waveform.If the output frequency required in 1 kHz. then the possible values of R1and R2can be respectivelya)2k, 1.7kb)4k, 2kc)2k, 4kd)1.7k, 2kCorrect answer is option 'A'. Can you explain this answer? tests, examples and also practice Electronics and Communication Engineering (ECE) tests.

Explore Courses for Electronics and Communication Engineering (ECE) exam