UPSC Exam > UPSC Questions > Design the general type of GO and NO GO gauge...
Start Learning for Free
Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it?
Most Upvoted Answer
Design the general type of GO and NO GO gauge for components having 30...
GO and NO GO Gauge Design for 30 H7/f8 Fit Components
Determination of Shaft and Hole Sizes:
- Given fit: 30 H7/f8
- Shaft tolerance grade f8: Upper deviation = -5.5D^0.41
- Diameter range: 18-30mm
- Using the formula i = 0.453D/3 + 0.001D to calculate the values of i for shaft and hole.
Calculation of Shaft and Hole Tolerances:
- IT7 = 16i
- IT8 = 25i
- Calculate the tolerance values for shaft and hole using the above formulas.
Designing the GO and NO GO Gauges:
- Determine the GO gauge size by adding the maximum shaft tolerance to the basic hole size (30mm).
- Calculate the NO GO gauge size by subtracting the minimum hole tolerance from the basic hole size.
- Apply the wear allowance (10% of gauge tolerance) to both GO and NO GO gauges to account for wear over time.
Finalization of GO and NO GO Gauges:
- Verify the dimensions of the GO and NO GO gauges to ensure they fall within the specified tolerances.
- Ensure that the GO gauge allows the maximum shaft size to pass through, while the NO GO gauge restricts the minimum shaft size from passing through.
- Test the gauges on sample components to ensure proper functionality and accuracy in determining the acceptability of the fit.
By following these steps, you can design the appropriate GO and NO GO gauges for components with a 30 H7/f8 fit.
Determination of Shaft and Hole Sizes:
- Given fit: 30 H7/f8
- Shaft tolerance grade f8: Upper deviation = -5.5D^0.41
- Diameter range: 18-30mm
- Using the formula i = 0.453D/3 + 0.001D to calculate the values of i for shaft and hole.
Calculation of Shaft and Hole Tolerances:
- IT7 = 16i
- IT8 = 25i
- Calculate the tolerance values for shaft and hole using the above formulas.
Designing the GO and NO GO Gauges:
- Determine the GO gauge size by adding the maximum shaft tolerance to the basic hole size (30mm).
- Calculate the NO GO gauge size by subtracting the minimum hole tolerance from the basic hole size.
- Apply the wear allowance (10% of gauge tolerance) to both GO and NO GO gauges to account for wear over time.
Finalization of GO and NO GO Gauges:
- Verify the dimensions of the GO and NO GO gauges to ensure they fall within the specified tolerances.
- Ensure that the GO gauge allows the maximum shaft size to pass through, while the NO GO gauge restricts the minimum shaft size from passing through.
- Test the gauges on sample components to ensure proper functionality and accuracy in determining the acceptability of the fit.
By following these steps, you can design the appropriate GO and NO GO gauges for components with a 30 H7/f8 fit.
Community Answer
Design the general type of GO and NO GO gauge for components having 30...
No
Attention UPSC Students!
To make sure you are not studying endlessly, EduRev has designed UPSC study material, with Structured Courses, Videos, & Test Series. Plus get personalized analysis, doubt solving and improvement plans to achieve a great score in UPSC.
|
Explore Courses for UPSC exam
|
|
Similar UPSC Doubts
Top Courses for UPSCView all
Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it?
Question Description
Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it? for UPSC 2024 is part of UPSC preparation. The Question and answers have been prepared according to the UPSC exam syllabus. Information about Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it? covers all topics & solutions for UPSC 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it?.
Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it? for UPSC 2024 is part of UPSC preparation. The Question and answers have been prepared according to the UPSC exam syllabus. Information about Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it? covers all topics & solutions for UPSC 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it?.
Solutions for Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it? in English & in Hindi are available as part of our courses for UPSC.
Download more important topics, notes, lectures and mock test series for UPSC Exam by signing up for free.
Here you can find the meaning of Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it? defined & explained in the simplest way possible. Besides giving the explanation of
Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it?, a detailed solution for Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it? has been provided alongside types of Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it? theory, EduRev gives you an
ample number of questions to practice Design the general type of GO and NO GO gauge for components having 30 H7/ f8 fit. Given that (a) i = 0.453 D/3 + 0.001D (b) upper deviation of 'f' shaft= -5.5D^0.41 (c) 30mm falls in the diameter step of 18-30mm (d) IT7 = 16i (e) IT8 = 25i (f) wear allowance = 10% of gauge tolerance. Can you do it? tests, examples and also practice UPSC tests.
|
|
Explore Courses for UPSC exam
|
|
Suggested Free Tests
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
|
© EduRev
|
Education Revolution
|
Follow Us
|
Signup to see your scores
go up within 7 days!
Access 1000+ FREE Docs, Videos and Tests
Takes less than 10 seconds to signup