A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer?

Explore Courses UPSC Exam UPSC Test Series Free Notes EduRev Infinity

Open App

GATE Exam > GATE Questions > A 150 mm diameter blind hole is to be drilled...

Join the Discussion on the App

A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 110⁰ . Machining time per hole (minute) __

Correct answer is between '0.6,0.7'. Can you explain this answer?

FREE This question is part of

Practice Test: Mechanical Engineering (ME)- 8

Attempt Test

Attempt this Test

Verified Answer

A 150 mm diameter blind hole is to be drilled upto 60mm depth at a spe...

View all questions of this test

View all answers Start learning for free

< Previous Question Next Question >

Explore Courses for GATE exam

Similar GATE Doubts

I n a single pass drilling operation, a through hole of 15 mm diameter is to be drilled in a steel plateof 50 mm thickness. Drill spindle speed is 500 rpm, feed is 0.2 mm/rev and drill point angle is118°. Assuming 2 mm clearance at approach and exit, the total drill time (in seconds) is

View answer

Blind holes of 20 mm diameter, 100 mm deep are being drilled in steel block. Drilling spindle speed is 600 rpm, feed is 0.2 mm/rev, point angle of drill is 135 °. During this operation, the drill wears out after producing 300 holes. Taylor’s tool life equation is of the form VT0.3 = C, where V = cutting speed in m/min and T = tool life in minutes Taylor’s constant C will be _____.

View answer

A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes. Correct answer is between '12,12'. Can you explain this answer?

View answer

A slot of 25 mm x 25 mm Is lo be milled in a workpiece of 300 mm length using a side and face milling cutter of diameter 100 mm, width 25 mm and having 20 teeth.For a depth of cut 5 mm, feed per tooth 0.1 mm, cutting speed 35 m/min and approach and over travel distance of 5 mm each, the time required for milling the slot is_______ minutes (round off to one decimal plac e). Correct answer is '8.1'. Can you explain this answer?

View answer

A propeller (diameter D = 15 m) rotates at N = 1 revolution per second (rps). To understand the flow around the propeller, a lab-scale model is made. Important parameters to study the flow are velocity of the propeller tip (V = ND) , diameter D and acceleration due to gravity (g). The lab-scale model is 1/100th of the size of the actual propeller.The rotation speed of the lab-scale model, to the nearest integer, should be _________ rps. Correct answer is '10.0'. Can you explain this answer?

View answer

A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer?

Share with a Friend

Answer this doubt

Question Description
A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer? for GATE 2024 is part of GATE preparation. The Question and answers have been prepared according to the GATE exam syllabus. Information about A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer? covers all topics & solutions for GATE 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer?.

Solutions for A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer? in English & in Hindi are available as part of our courses for GATE. Download more important topics, notes, lectures and mock test series for GATE Exam by signing up for free.

Here you can find the meaning of A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer? defined & explained in the simplest way possible. Besides giving the explanation of A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer?, a detailed solution for A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer? has been provided alongside types of A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer? theory, EduRev gives you an ample number of questions to practice A 150 mm diameter blind hole is to be drilled upto 60mm depth at a speed of 500 rpm and feed 0.2 mm per revolution, point angle of drill is 1100. Machining time per hole (minute) __Correct answer is between '0.6,0.7'. Can you explain this answer? tests, examples and also practice GATE tests.

Explore Courses for GATE exam