GATE Exam > GATE Questions > A block of length 200mm is machined by a slab...
Start Learning for Free
A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.
Correct answer is between '12,12'. Can you explain this answer?
| FREE This question is part of | Download PDF Attempt this Test |
Verified Answer
A block of length 200mm is machined by a slab milling cutter 34mm in d...
Milling Time 
Where, D = Dia of cutter (mm), d = depth of cut (mm)
L = length f = feed (mm/ min)
L = length f = feed (mm/ min)
Most Upvoted Answer
A block of length 200mm is machined by a slab milling cutter 34mm in d...
To calculate the minimum estimated machining time per pass, we need to consider the approach and over travel of the cutter.
Given data:
- Length of the block (L): 200 mm
- Diameter of the slab milling cutter (D): 34 mm
- Depth of cut (d): 2 mm
- Table feed (f): 18 mm/minute
Approach and Over Travel:
- Approach: It is the distance the cutter needs to travel to reach the starting point of the cut.
- Over Travel: It is the distance the cutter needs to travel after completing the cut.
Approach and over travel are equal in this case, so we can consider their combined distance as the minimum distance the cutter needs to travel per pass.
Calculating the minimum estimated machining time per pass:
1. Calculate the number of passes:
- The total depth of cut is given as 2 mm.
- Since the depth of cut per pass is also 2 mm, the number of passes required can be calculated as L/d.
Number of passes = L/d = 200 mm / 2 mm = 100 passes
2. Calculate the minimum distance the cutter needs to travel per pass:
- The total length of the block is given as 200 mm.
- The diameter of the cutter is given as 34 mm, so the effective length of the cut per pass is (L - D).
Effective length of cut per pass = L - D = 200 mm - 34 mm = 166 mm
3. Calculate the total machining distance:
- The total machining distance is the sum of the approach distance, the effective length of cut per pass, and the over travel distance.
Total machining distance = Approach + Effective length of cut per pass + Over travel
Total machining distance = (L - D) + (L - D) + (L - D) = 3(L - D)
4. Calculate the minimum estimated machining time per pass:
- The table feed is given as 18 mm/minute.
- Divide the total machining distance by the table feed to get the minimum estimated machining time per pass.
Minimum estimated machining time per pass = Total machining distance / Table feed
Minimum estimated machining time per pass = 3(L - D) / f = 3(200 mm - 34 mm) / 18 mm/minute ≈ 12 minutes
Therefore, the minimum estimated machining time per pass is approximately 12 minutes.
Given data:
- Length of the block (L): 200 mm
- Diameter of the slab milling cutter (D): 34 mm
- Depth of cut (d): 2 mm
- Table feed (f): 18 mm/minute
Approach and Over Travel:
- Approach: It is the distance the cutter needs to travel to reach the starting point of the cut.
- Over Travel: It is the distance the cutter needs to travel after completing the cut.
Approach and over travel are equal in this case, so we can consider their combined distance as the minimum distance the cutter needs to travel per pass.
Calculating the minimum estimated machining time per pass:
1. Calculate the number of passes:
- The total depth of cut is given as 2 mm.
- Since the depth of cut per pass is also 2 mm, the number of passes required can be calculated as L/d.
Number of passes = L/d = 200 mm / 2 mm = 100 passes
2. Calculate the minimum distance the cutter needs to travel per pass:
- The total length of the block is given as 200 mm.
- The diameter of the cutter is given as 34 mm, so the effective length of the cut per pass is (L - D).
Effective length of cut per pass = L - D = 200 mm - 34 mm = 166 mm
3. Calculate the total machining distance:
- The total machining distance is the sum of the approach distance, the effective length of cut per pass, and the over travel distance.
Total machining distance = Approach + Effective length of cut per pass + Over travel
Total machining distance = (L - D) + (L - D) + (L - D) = 3(L - D)
4. Calculate the minimum estimated machining time per pass:
- The table feed is given as 18 mm/minute.
- Divide the total machining distance by the table feed to get the minimum estimated machining time per pass.
Minimum estimated machining time per pass = Total machining distance / Table feed
Minimum estimated machining time per pass = 3(L - D) / f = 3(200 mm - 34 mm) / 18 mm/minute ≈ 12 minutes
Therefore, the minimum estimated machining time per pass is approximately 12 minutes.
|
Explore Courses for GATE exam
|
|
Similar GATE Doubts
A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer?
Question Description
A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer? for GATE 2024 is part of GATE preparation. The Question and answers have been prepared according to the GATE exam syllabus. Information about A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer? covers all topics & solutions for GATE 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer?.
A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer? for GATE 2024 is part of GATE preparation. The Question and answers have been prepared according to the GATE exam syllabus. Information about A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer? covers all topics & solutions for GATE 2024 Exam. Find important definitions, questions, meanings, examples, exercises and tests below for A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer?.
Solutions for A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer? in English & in Hindi are available as part of our courses for GATE.
Download more important topics, notes, lectures and mock test series for GATE Exam by signing up for free.
Here you can find the meaning of A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer? defined & explained in the simplest way possible. Besides giving the explanation of
A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer?, a detailed solution for A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer? has been provided alongside types of A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer? theory, EduRev gives you an
ample number of questions to practice A block of length 200mm is machined by a slab milling cutter 34mm in diameter. The depth of cut and table feed are set at 2mm and 18mm/minute, respectively. Considering the approach and the over travel of the cutter to be same, the minimum estimated machining time per pass is _____________ minutes.Correct answer is between '12,12'. Can you explain this answer? tests, examples and also practice GATE tests.
|
|
Explore Courses for GATE exam
|
|
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
|
© EduRev
|
Education Revolution
|
Follow Us
|
Signup to see your scores
go up within 7 days!
Access 1000+ FREE Docs, Videos and Tests
Takes less than 10 seconds to signup